How can I calibrate a saturated calomel electrode?

More Saeed Rahman's questions See All

What is causing my nyquist plot to look almost opposite to a common Nyquist plot ?

05 June 2015 8,808 6 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View

Is that possible to do an impedance measurement without FRA module?

One of my colleagues said, "the impedance you can measure with the three electrodes and with the specific sequence varying the frequency" Is it possible to configure the potenciostat without the...

21 February 2021 418 2 View

Do you know this error? The experiment was stopped by a potential overload on Vs (auxiliary electrode)?

Hello everyone Do you have any information about this error 'The experiment was stopped by a potential overload on Vs (auxiliary electrode)' in Origamaster software? I tried everything possible,...

19 February 2021 3,152 7 View

Which compound is getting oxidized during bulk electrolysis with TFAA?

The experiment is really simple. When I do a bulk electrolysis with 1% TFAA (ACN solution) to get dihydrogen, what is going to be oxidized? (working electrode graphit, counter electrode platinum,...

18 February 2021 4,430 1 View

Not able to charge-discharge Li-ion coin cell at higher C rate ?

I am working on cathode material. I have made different Li-ion coin cell against Li metal using commercial available cathode materials such as LCO,LMO, LFP and NMC and also with the lab...

18 February 2021 1,450 3 View

Isaiah Gyan Popular answer

You should obtain another reference electrode you trust and using a regular voltmeter, you can check the validity of your SCE in NaCl. See page 26 of the pdf in the link below. If you can't download it, let me know and I will get it for you.

http://www.basinc.com/mans/epc.pdf

Isaiah Gyan

Qijin Chi

Isaiah has given a correct answer with the simple (or standard) method. In addition, just in case you only have one SCE, then you can also use Ag/AgCl reference electrode or test a well-known redox probe such as ferrocene.

Julio Cesar Bastos Fernandes

Dear Mr. Rahman, maybe you can use a standard cell of Weston (see link: https://en.wikipedia.org/wiki/Weston_cell). This cell presents a ddp of 1.018 Volts, whose value is mantained the same by years. Using a simple circuit with a galvanometer (in attachment) you can measure the potential of calomel electrode. You can also use a pHmeter, but you have to adapt the connector. The construction of Weston cell is not complicated (http://conradhoffman.com/stdcell.htm or http://www.nist.gov/calibrations/upload/mn84.pdf), but you can buy. However, this cell is very stable, therefore may be difficult find it to buy. This is a sugestion. I hope to have helped you. Good lucky.

A. Naeemy

u can use KMnO4 solution

Alaa A. El-Shafei

you can check it against any reference electrode, probably better with SHE

Chinnapiyan Vedhi

the electrodes of SCE and Pt immersed in 1M KC1 and connect any one digital potentiometer and measure total potential. then you compared with std potential and clear you.

Richard A Durst

I happened to look at the reference that Dr. Gyan suggested, which is a BAS manual, and was surprised to read that NaCl is used in their Ag/AgCl electrodes. Does anyone know why they use this salt rather than the more equitransferent KCl electrolyte as used in most other reference electrodes and salt bridges? I note that BAS uses KCl in their SCE, however.