Hello I am trying to calculate the Power-delay product (PDP) for Tunnel FET. So is there is a way to calculate, estimate or simulate the device.
Dr. Shiromani:
Best regards. We have been in communication before. Please check these papers if you have not gone through them already. If my answer is useful to your question, please recommend my answer.
Sincerely,
Dr. Nabil Shovon Ashraf
Associate Professor
Department of ECE
North South University
Dhaka, Bangladesh.
1. A bcc metal single crystal was sliced along (1 -1 0) plane for TEM study. Assuming that the TEM available is equipped with a goniometer stage which tilts up to 45o. The Burgers vector of...
20 February 2021 2,370 1 View
I have made neosome from herbal drug. Neosomes are stable. But I face problems in dissolution. I used minimum ratio of 1:1:0.25 ( Drug:span 60: Cholesterol and GMs. Now how can I active better...
17 February 2021 3,584 1 View
We are planning to make Polymeric nanoparticles for co-delivery of 2 flavanoides. Which is the best method, that one should follow.
09 February 2021 7,086 8 View
Hello, Has anybody published with OmniScriptum Publishing Group. I got an email from them. The emails claims the editor is from the group but the email is signed out by lambert academic...
08 February 2021 5,611 3 View
Even after few repetitions..I am getting similar results. Is is due to organic components?
20 January 2021 9,279 6 View
To have the desired grain size in 6061 and 6063 Al alloy, what should be the minimum % of Ti and B pick up and what is the chemistry/metallurgy behind that?
07 January 2021 9,305 2 View
Kindly provide the technical papers/patents on the production of AlV50% alloy by thermit route, by using V2O5
05 January 2021 2,471 3 View
FeAl and Al wire has applications in Steel for deoxidation. I want to know the other application of various grades of FeAl. Does Al wire also has other applications apart from deoxidation? Regards
27 December 2020 8,435 1 View
There is a different behavior in carbon steel and stainless steel. Drastic low recovery in carbon steel due to high melting temp. But in ss , working temp is high so dissolve at 1668 degree temp....
16 December 2020 8,765 8 View
I need Coronary Angiogram Images(CAI) publically available dataset. Coronary Artery Disease (CAD) is a condition of the heart due to atherosclerosis. Atherosclerosis is the narrowing of arteries...
07 December 2020 6,470 3 View
I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...
03 March 2021 1,931 5 View
I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...
02 March 2021 1,408 1 View
Working on chandrayaan-2 DFSAR data, there are three datasets available: 1) Slant range image data product: The slant range complex image file. Each pixel is represented by two 4-byte floating...
02 March 2021 8,481 3 View
My study consists simple corrosion inhibitors in salty brine. Right now I just fit my circuit with randles with CPE. Just wondering how the slop can given more info of the experiment. Or any...
01 March 2021 6,474 3 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...
28 February 2021 2,116 1 View
Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...
28 February 2021 7,016 1 View
I have a doubt on how to select the inductor and capacitor value when I want to implement MPPT controller. This is because we always take a maximum output voltage and current but in this case, we...
28 February 2021 3,637 2 View
I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...
26 February 2021 1,511 3 View
Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...
25 February 2021 8,749 6 View