Is it possible to do Reitveld Refinement on single crystal XRD data?

I tried to do single-crystal Rietveld Refinement on my single-crystal XRD data using the option "refinement on single-crystal data/ integrated intensity data" in Fullprof but it is giving error...

30 January 2021 7,813 3 View

What will be the impact on Antenna performance to shift the resonant frequency by RLC Matching network?

There is always a possibility to shift the resonance frequency by adding a RLC matching network. I wonder what will be the consequence on antenna performance (axial ratio, gain)? If there is no...

13 September 2020 5,187 3 View

Axial ratio shows different result at different ortogonal setup. What could be the reason ?

17 June 2020 5,332 3 View

Firm survival and mortality: How to relate both?

I have two data sets 1. Age of all the surviving firms at any given point of time. The age distribution is an exponential function 2. The age of all the firms which died at a given point of time (...

01 February 2020 3,542 1 View

Why Antenna shows negative gain even though it has very good matching?

I am aware of the fact that electrically small antennas are poor radiators with very small gain and low efficiency. One main cause of this is poor matching. An extremly electrically small antenna...

19 January 2020 5,285 9 View

What is the impact of image current from ground plane on patch antenna? I wonder how it radiates if ground plane is very near to radiator?

As we know, patch antenna is combination of two magnetic dipole. If we place a perfect electrical conductor near a dipole, antenna performance will suffer significantly. Then how a patch antenna...

27 November 2019 7,597 5 View

I am getting two peaks at 702 and 705 eV for Fe 2p scan of a composite made from Fe-salen.how it can be explained?

the pure Fe-salen spectra is in conformity with literature,but the composite is showing two extra peaks at 702 and 705 eV. Can anybody explain about why the peaks are coming.

23 July 2019 5,710 3 View

What will be the cororidinate(theta and phi) to evaluate the axial ratio?

I have designed a circular polarized antenna. But , I am confused with cor-ordinate system. In some angel it shows less than 2 dB axial ratio and some other point it shows more than 10 dB like a...

23 May 2019 2,175 7 View

Why there is a big difference in between realize gain and gain in my design?

I have designed a multiport antenna. Where as, I have 2 dB Gain but realize gain is -6 dB. Point to be noted, S11 is really good. I have -25 dB return loss at my desired frequency.

22 November 2018 6,165 17 View

Bands in western blot are behaving like GHOST!!!!!!!!!!!!!!!!!?

I am doing western blot and after development I can see that one/ two lanes have no band. Perhaps, next day I am doing same gel run with same sample with no change in protocol, this time another...

25 September 2018 8,325 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View