How can i calculate percentage peak area in gas chromatogram?

More Haresh Kalasariya's questions See All

Is there any bioinformatic tools or technique for predicting skin cosmeceutical activities of chemical compound?

Except PASS, by using PASS, we can predict biological activities.. Any other tools?

12 January 2021 7,188 1 View

How to collect dandruff sample from head?

I want to isolate fungi responsible for causing dandruff. Is there any special media as well as sample collection procedure of it?

26 August 2020 2,141 3 View

How to detection the gunidine hydrochloride by HPLC??

08 January 2018 8,788 3 View

What is the consequence of having singular gluon propagator in some gauge? Is it fine?

What can we say about the usefulness of this gauge in ultraviolet and infrared region?

23 October 2014 6,302 3 View

Dilution problems related to oils solubility of Lornoxicam.

I am preparing microemulsion of Lornoxicam, which is soluble in 7.4 pH buffer and 0.1 N NaOH, but in the screening of various oils, I have to dilute the saturated solution of drug in oil. However,...

04 February 2013 3,581 2 View

How to do transient duty cycle analysis in ANSYS ?

Heater of 0.5 Watt is applied on Aluminium cylinder to get expansion by temperature increase. I want to calculate duty cycle during which heater must keep ''on'' to get 10 degree temperature...

01 January 1970 7,841 3 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Why do a weight decrease for thermal degradation in nitrogen gas condition?

Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...

26 February 2021 1,100 5 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Aspen Plus Error: Unknown or undefined bead number?

Hello, in my Aspen Plus Simulation (see attachment) there are two heat exchangers. One HEX1 (oil+gas) ist fed by hot gas which ist coming out of a burner. The other HEX2 (gas+gas) shall work as a...

14 February 2021 8,096 2 View

NVT or NPT is preferable for gas adsorption simulation ?

Hi there, In order to perform molecule dynamic simulation on gas adsorption on substrate materials, NVT or NPT ensemble is preferable ? Thanks!

08 February 2021 173 1 View

How can I convert permeability unit from barrer to m^2 for using COMSOL MultiPhysics?

I am looking for gas permeability of PDMS for simulation in COMSOL MultiPhysics and using creeping flow , fluid and matrix properties. The permeability unit in COMSOL is m^2 whereas I have the...

08 February 2021 4,305 2 View

Any reference paper with detailing on how to hybradize Q-Learning algorithm with Genetic Algorithm, especially for a variable optimization problem?

I am planning to hybradize Q-Learning algorthm with Genetic algorithm at the population initialization stage, crossover stage and mutation stage. The problem under consideration is a...

07 February 2021 3,123 8 View

William Letter

Add peak areas to find total. Divide area by total to find percentage.

Massoumeh Farasat

You can use this link to calculate the peak area.

http://faculty.sdmiramar.edu/fgarces/LabMatters/ChemTech/modules/gaschrom/gaschromcalc.htm

Haresh Kalasariya

Massoumeh Farasat I have calculated accordingly, will you please check the below-calculated results. (Excel file, sheet 2)

I am also attaching the Chromatogram report, PFA.

William Letter I have calculated accordingly, will you please check the below-calculated results. (Excel file, sheet 2)

Yuhta Nomura Thanks sir, I have a chromatogram report, PFA

Your suggestions are highly valuable to me

Method quality is questionable so results obtained may be invalid. Area counts are also inaccurate because the integration parameters have errors. Correct your integration (or method) before moving forward. *As shown, your method and results are invalid.

I agree with William.