Please give me some procedures to apply froth flotation to separate low grade monazite from silicates. Which chemical agents (collectors, frother, co-collector, pH modifier) might be used?
Dear Farhad, salam
Pl see "Handbook of flotation reagents", Vol. 2, Chapter 24. You can find useful information about REO minerals flotation in this book.
Regards
Which is the best method for the characterization of beta cyclodextrin complex formation with guest molecule in solution form and in solid form ?
11 June 2024 6,719 0 View
calculate genome-wide iHS values > breed_wgscan_ihs
01 March 2024 1,775 0 View
Dear friends. Recently, I performed an economic inequality of blinder-oaxaca decomposition on Fatty Liver Disease (FLD). I obtained a difference of -0.06 between high and low economic status....
23 December 2023 6,831 0 View
The fantastic tree Moringa oleifera is a perennial tree. In literature, I see moringa being referred to as Annual moringa and Perennial moringa. What are the basis for these terminology? Is there...
09 December 2023 8,364 0 View
Hello all, Regarding self-healing hydrogels, can only the covalent Schiff-base bond break and form quickly, or do other bonds give this self-healing property to the hydrogel?
28 October 2023 1,050 3 View
Hi, Does anybody know the procedure for dissolving TPU in DMF? I mean a 40% TPU in DMF, I wan to do the dip molding Thanks, Temp, type of agitation, drying the resin,..
23 September 2023 580 0 View
Hi, can you help me with a resource for dissolving TPU in DMF? what temperature? drying resin? type of agitation and impeller? also casting.
22 September 2023 1,158 2 View
I am writing to seek guidance on how to access articles from the American Speech-Language-Hearing Association (ASHA) for my research work in 2023. ASHA's resources are known to be invaluable for...
14 September 2023 2,962 1 View
I hope this message finds you well. I am currently in need of access to iThenticate for my research and academic work. However, due to budget constraints, I am exploring the possibility of...
14 September 2023 2,247 2 View
Hi everybody I recently graduated with Msc. in Computer Engineering. I am searching for a Ph.D. position at universities in Canada. Is there a quick way to find a supervisor with a specific...
12 August 2023 8,147 2 View
How can I select cells in prime editing without fluorescence-activated cell separation?
31 July 2024 8,551 2 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...
13 July 2024 9,003 2 View
I am preparing polycrystalline diamond (PCD) with tape casting. The powder is 8~12 um. After drying of tapes, I place several tapes in Ta cup without warm-pressing. Next, debinding is carried...
23 June 2024 7,758 2 View
I am trying to sinter my samples at 1300 degree celsius in Vacuum and I came to know about a technique from some lab technicians that it can be done using box or muffle furnace itself. The idea is...
26 May 2024 9,850 4 View
Dear Experts, I am currently conducting a Molecular Dynamics (MD) simulation using the NAMD package to observe the formation of a two-phase system between glucose, acetonitrile, and water. To...
26 May 2024 5,711 2 View
Need a simple and small scale preparation methods
23 May 2024 3,843 0 View
Hello everyone! I am working on PVDF-based membranes for dye rejection and have encountered a recurring problem: after each rejection cycle, the membrane flux increases rather than decreases,...
20 May 2024 2,107 1 View
I attempted a phosphate (apatite) flotation, but the slurry was too thick for the impeller to work properly. I reduced the solid content to 30% for better mixing, but the conditioning still seems...
14 May 2024 4,505 4 View