How can I add two axis markers in a plot at CST Studio Suite without using measure lines as an alternative solution?

Stavros Togkousidis @Stavros-Togkousidis

09 October 2024 0 7K Report

The indication d of the measured range in S parameter graph in CST Studio Suite is overwritten by the title of the graph and can not be read. How can I move the title over the indication of range or even better remove the indication. I want to to have two axis markers in one plot and I see that this can be only achieved in a way by adding the measure lines. Is there any other option?

Badges
Science method

More Stavros Togkousidis's questions See All

How to access Axis Marker Properties in CST Studio Suite?

How can I change marker axis line type to dotted in 1D Results/S-Parameters in CST Studio Suite?

10 June 2024 9,828 0 View

Does anybody know the average cost of AURA NIR handheld analyzer ?

ZEISS (manufacturer)

09 May 2024 3,329 0 View

Alternative Framework(s) to PICO?

I am about to conduct a scoping review which will identify and map the available evidence of a topic in policing. The review will draw on a realist evaluation framework...

26 February 2024 5,823 0 View

Do you have any suggestions for grey literature related to police work?

Any ideas apart form the College of Policing, National Police Chief’s Council and Opengrey, please. I want to search articles for my literature review.

27 November 2023 3,585 5 View

Is it possible to blast sequences with blast discontinous sequences with ncbi blastn?

I might be going the wrong way about this, but is there a way to check if two or more sequences are present on the same gene? The reason I want to do it: I've designed primers and taqman probe...

06 November 2021 7,173 2 View

While submitting ITS sequence on NCBI how do I include CDS data?

I have to submit ITS sequences (but the principle should be the same for every gene) on ncbi. How do I include CDS data. For ITS it is: 18s, ITS1, 5.8s, 28s? I tried using the default tool but it...

30 August 2021 7,680 3 View

When is the right time to stop training a classification algorithm?

In this example giving 400 samples looks like there is an accuracy of 91.5% while training beyond that point, accuracy is getting decreased. Are 400 samples enough to keep for this example? If...

27 January 2021 6,010 3 View

Designing Taqman primers, probes - differentiating species - what's more important?

I need to design Taqman probes for different species of the same genus in order to differentiate between them. I have read the guidelines (no 5' G end on probe, max 2 GC 3' end primers, ~10C...

29 December 2020 5,044 1 View

Preparing and reviving mycelial/ conidial glycerol stocks - how to and tips?

I have an issue with reviving mycelial/ conidial glycerol stocks from the -80 freezer. The fungi I'm working with belong to the Botryosphaeria and Neofusicoccum species. I prepare the conidial...

05 December 2019 9,372 0 View

Category 3 PRIIP MRM calculation - How to derive risk-neutral returns from the bootstrapped historical simulation returns?

My question is concerned with the commission delegated regulation (EU) 2017/653 (https://eur-lex.europa.eu/legal-content/EN/TXT/PDF/?uri=CELEX:32017R0653&from=EN) on standardizing the...

12 December 2018 9,286 0 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

Entropy measure and QSPR modeling in Graph Theor. How to construct the table for lengthy equation?

The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...

30 July 2024 3,126 0 View

There is possible way to calculate experimental DOS from the UPS spectrum of the material. How to calculate the DOS from UPS?

Here, I have attached the UPS graph. I'm trying to calculate the DOS/DOVS from the UPS.

29 July 2024 4,971 1 View

How to know the b axis of a single crystal?

How to apply magnetic field parallel to b axis of any crystal

29 July 2024 4,083 2 View

MAGeCK Plotting Error: Logarithmic Axis Must Have Positive Limits?

I have been running a MAGeCK test command on the terminal for a CRISPR screen to rank sgRNAs and genes based on the read count tables. However, I get only the plot of the top-ranked genes...

28 July 2024 9,811 1 View

Critique Calculaltion in Topological Indices and QSPR Modeling?

The first step is to analyze a 2D molecular graph and implement partitioning techniques to calculate the topological indices. Secondly impose statically tools to generate QSPR model, may or may...

24 July 2024 9,644 1 View

How to do calculation of Louvain methods calculation for excel sheet and and is there any software available?

The Louvain method – named after the University of Louvain where Blondel et al. developed the algorithm – finds communities by optimizing modularity locally for every node’s neighborhood, then...

23 July 2024 6,659 0 View

Is there a name for this type of function?

Let n∈ℕ, where the function f:A⊆ℝ𝑛→ℝ, 𝐴 is Borel, and (A,d) is a completely seperable space. What is the name of the functions where the graph of f in any (n+1)-dimensional box of A×ℝ is...

17 July 2024 258 1 View

How can I define Planetary motion in ABAQUS CAE, how define motion of three rollers around a central axis and passive rotation about their own axis?

16 July 2024 4,145 1 View