I want to remove the oxide layer on aluminium metal inside a nitrogen glovebox. Is this feasible to do? It is for use in an aluminium battery.
Jacob Johnston
You can thoroughly and gently polish your aluminum foils using pieces of sand paper.
Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...
10 August 2024 8,992 0 View
I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...
03 August 2024 3,851 1 View
I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...
03 August 2024 6,070 3 View
HI there, I've came across several articles discuss about random audit an Non random to tax evasion or compliance. Most of the articles is relating about effect of audit (random or non random)...
31 July 2024 5,309 7 View
I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...
31 July 2024 9,697 0 View
Please suggest basic literature on lattice-based cryptography. A kind response from the cryptographic community will be highly appreciated.
24 July 2024 6,291 4 View
I want to know that n-doped side of solar cell is connected with positive or negative electrode.
20 July 2024 1,348 2 View
Bioinformatics tools like peptide cutter
15 July 2024 6,453 1 View
Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...
15 July 2024 3,491 0 View
Dear all, I am looking for FACS markers to characterize my rat bone marrow-derived macrophages (M0). They were differentiated from monocytes with M-CSF. I am considering to use CD11b/c and...
15 July 2024 4,615 1 View
The paper in question is "Interpolation of Nitrogen Fertilizer Use in Canada from Fertilizer Use Surveys". This paper was very recently published by Agronomy (MDPI). Agronomy has, in the last day...
07 August 2024 9,934 3 View
I imagine the battery drives the graphite into a carbocation, then chloride is oxidized to donate the electron to the carbocation, but what pushes the lost electrons of chloride to be shared...
03 August 2024 5,384 0 View
Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...
03 August 2024 5,358 0 View
I am an Mphil research student and looking for high impact factor battery related journals to download and read research articles to improve my knowledge and get new ideas in the field of battery...
01 August 2024 6,516 2 View
What is the best way to freeze the rat brain - liquid nitrogen, Dry ice , isopentane - after isolation for later protein investigation by Elisa?
01 August 2024 1,722 1 View
How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...
26 July 2024 8,281 0 View
I have attached the charging curve from the battery tester for review. I need help on what is happening
21 July 2024 6,898 2 View
Our lab has some radioactive cell samples that need to be kept frozen for at least 30 days before flow analysis. For some reason, the samples stored in liquid nitrogen did not perform as well as...
15 July 2024 9,975 1 View
I need to plot cycle number vs. capacity with multicurrent density. please let me know if my steps are right or not as the below picture
14 July 2024 7,702 2 View
Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?
10 July 2024 8,763 0 View