Hi Sridhar, Can I help in anything with in this project?

01 January 1970 1 8K Report

In coating steel interface, for instance.

Hello George;

Most of the work done is to characterize Cu coating properties. However, I will let you know if there is a need to characterize iron corrosion products.

Best Regards,

Sridhar.

Badges
Science topic

More Jerzy A. Sawicki's questions See All

How accurate the EDX analysis can be in the case of nano sized precipitates of Nb with 10wt%Zr and 5wt%Fe in zirconium matrix containing 0.3wt%Nb?

In so called fully-transformed by prolonged heat treatment below-near 580oC zirconium with 2.5wt%Nb-0.1wt%Fe alloy the Nb particles precipitate with the expected concentration of 10wt%Zr and...

02 March 2015 7,947 12 View

Can electron microscopy be used to determine the volume fraction of second phase nanoparticles in the alloys like Zr-2.5wt%Nb-0.1wt% Fe?

Such beta-phase particles can be in size range of 10 - 20 nanometers and in the matrix or grain boundaries of alpha-Zr grains.

31 December 2014 9,674 3 View

Is it possible to make niobium alloy with ~10 wt% Zr and ~3 wt% Fe in solid solution?

Zirconium alloys are used in the core of nuclear reactors. Some of them contain 1 to 3 wt% Nb and ~0.1 to 0.2 wt% Fe. I observed in them the tiny precipitates of cubic beta-Nb phase with ~10 wt%...

11 December 2014 9,550 7 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View