Hi, How can change polarization of incident field in RCWA solver in Lumerical FDTD?

13 August 2024 1 433 Report

In the RCWA solver, only the excitation tab exists where there is no information about polarization. So, how can I change the polarization

Şükrü Aktaş

Açı, dalga boyu, Frekans değerleri girilerek ve dalga boyu özelliği kutucuğu işaretlenerek işlem yapılır.

More Ibnun Nur Akash's questions See All

How to preform densitometry on SDS-page bands?

I ran a SDS-page of a bacterial lysate and I want to quantify protein concentration in a specific band. I was thinking of using a standards ladder or make some standards are different...

05 August 2024 9,805 3 View

There is possible way to calculate experimental DOS from the UPS spectrum of the material. How to calculate the DOS from UPS?

Here, I have attached the UPS graph. I'm trying to calculate the DOS/DOVS from the UPS.

29 July 2024 4,971 1 View

Is there a subtle distinction between the terms "substitution" and "doping"?

Dear Prof, is there a subtle distinction between the terms "substitution" and "doping" when referring to modifying ceramic dielectric materials for example Na0.5Bi0.5TiO3? Is there any difference...

08 July 2024 2,043 3 View

Problems/ Challenges regarding Dark Tourism?

Im currently writing my Thesis on Challenges/ Problems/ Particularities regarding Dark Tourism and have a little trouble finding the right literature. I have found a lot of literature for dark...

14 June 2024 7,262 2 View

When IC50 cannot be obtained according to the cell viability chart, what should be the dose selection under cell culture conditions?

When IC50 cannot be obtained according to the cell viability chart, what should be the dose selection under cell culture conditions? Would it be beneficial to go with sham control? For example,...

11 June 2024 9,109 0 View

How to calculate my FRAP Assay?

Y=0.0011x+0.1031 (Standard curve eq) Chamomile sample 20mg/mL Absorbance(y)= 1.16 x=960.82(µg/mL) Chamomile sample 10mg/mL Absorbance(y)= 0.80 x=633.55(µg/mL) Tridax sample...

01 June 2024 7,843 0 View

What are the long-term functional and aesthetic outcomes of autologous vs alloplastic materials in facial reconstructive surgery following trauma?

This question aims to explore the comparative effectiveness of using a patient's own tissue (autologous) versus synthetic materials (alloplastic) in facial reconstructive procedures, focusing on...

25 May 2024 1,791 0 View

How to determine the concentration of MXene colloidal solution?

Dear researchers, I have recently synthesised MXene by etching MAX phase source using in-situ fluoride based etchant and collected the supernatant solution obtained after the washing process. My...

22 May 2024 5,269 2 View

Request for help in compiling Lammps files (including cpp an dh header files) using cmake in ubuntu ?

Hi, I am working on LAMMPS molecular simulation on CO2 mineralization. I have some scripts which require to compile Lammps files using cmake in ubuntu. Is there anyone who has some expertise can...

20 May 2024 5,026 2 View

Do your country have Psychology Acts?

Hi/Salam; Did your country establish "Psychology Acts" for psychologists to practice? I just discovered that Malaysia still does not have the Psychology Acts for psychologists to practice, where...

13 May 2024 6,921 6 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

What is the right voltage sweep direction for characterization of HER kinetics?

In general, when performing a Tafel analysis for corrosion resistance measurements, a line voltage scan is performed from say -250 to +250 mV vs. OCV at low scan speed around 0.125 mV/s. However,...

25 July 2024 7,982 3 View

What should I upgrade in my computer to speed up simulation in CST?

I want to reduce simulation time in CST for frequency domain solver by upgrading my computer. I already have discrete GPU but it doesn't seem to make any difference at all compared to integreted...

10 July 2024 2,789 4 View

What is co-polarization and cross polarization? How can plot it from CST studio?

what is co-polarization and cross polarization? How can plot it from CST studio? what are steps and process for find out co-polarization and cross polarization from CST studio?

08 July 2024 7,869 1 View

What's wrong with my COMSOL model for turbulent flow in time dependent solver?

I am trying to simulate velocity field inside a domain of just ambient air (pressure is 1 atm & velocity is 10 m/s). There is a tank inside it which has a leakage. The leakage hole is leaking...

01 July 2024 2,249 0 View

How to calculate corrosion rate from potentiodynamic polarization test data for dissimilar welds?

we need surface area, corrosion current, equivalent weight and density of the metal involved for corrosion rate calculation in mm/year (lets say). For dissimilar metal welds, how can we measure...

30 June 2024 5,943 2 View

How to find the incident spectra in Lumerical FDTD?

Hello, I am having a difficult time finding the incident plane wave wavelength dependent spectra of the lights source to find the EQE. Please advise.

26 June 2024 7,274 1 View

How to Compare Tafel plots in different KOH concentration?

I have to compare overpotential and current density of different materials from tafel plots. These tafel plots have obtained in different concentrations of aqueous solution. How do I compare these...

24 June 2024 6,399 2 View

How to create ITO materials in FDTD?

Here are the ITO material parameters and the Drude model I found in an article, but I don't know how to import these parameters correctly into Ansys lumerical FDTD.The attached picture shows the...

18 June 2024 3,182 10 View

How to create ITO materials in FDTD?

12 June 2024 5,915 2 View