Hello, i have NMR spectre of inorganic compound which is contain peaks in negative ppm and others in positive ppm, so how can i interpret it?

15 March 2025 1 6K Report

What can i do whith negative ppm, i take it as they are or i shift all peaks to positive part, and what is about the aromatic peaks?

Dilip Sarkar

You will use mestronova software for interpretation for your dada. You can set the ppm range there.

Badges
Science topic

Similar topics
Physical Sciences
Optics

More Zouaghi Hanene's questions See All

Why can't observe plaque in double agar layer plates after M13 phage infection of TG1 ?

We try to titer our M13 phage using double agar layer plates, but we couldn’t see any plaque after plate incubation. However, colonies can be observed on the plate containing antibiotic...

02 December 2022 7,563 0 View

How much water we should add to paint if we use a based water binder (resin) or there is no need for adding water with such binder?

I want to know if the water included in resin is enough as a solvent or that water is not counted and I should add water as solvent to paint?

21 June 2020 537 6 View

Calculate current efficiency in the case electrochemical denitrification

how to calculate current efficiency (in the case of electrochemical denitrification in wastewater where there is a lot of reactions with nitrates and by products ?? it possible to add different CE ??

23 September 2014 2,990 3 View

How to interpret graphs of moderation

I want to make a legend to explain a moderation chart so to mention the levels, the green line corresponds to the high level of moderator, the blue line at the low level but what to say for the...

01 January 1970 4,125 0 View

Melt curve problem in qPCR?

Do these peaks in the curve indicate primer dimer or non-specific products?

01 August 2024 7,466 0 View

How to improve peaks separation in HPLC?

Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...

30 July 2024 435 3 View

What does an additional peak in FTIR between 3100 and 3300 nm affect the quality of the material, benzethonium chloride USP??

I do not know much about FTIR! The material Benzethonium Chloride USP was compared to a reference standard in regards to FTIR, as per the USP testing: Identification B. Infrared absorption (FTIR),...

16 July 2024 6,918 7 View

Validated HPLC method for the estimation of the Amphotericin B ?

During the release test of Amphotericin B using 1% Tween 80, i observed three peaks even in the standard. The first peak consistently yielded results around 500%, while the other peaks showed...

08 July 2024 1,330 0 View

Why there are no peaks at downfield NMR of Cobalt and Nickel complexes?

I synthesized some paramagnetic cobalt and nickel complexes (expected to be Co(II) and Ni(II)) using a bidentate ligand - N of pyridine ring (aromatic) and O of P=O (aliphatic), and I obtained...

03 July 2024 3,410 4 View

How can I put small FWHM in CasaXPS?

I'm trying to fitting Cu Auger peak into various state (Cu0, Cu+, CuI etc..) In Cu0, one of the peak's FWHM is 0.84 but when I try to enter smaller value than 0.89, "input error" is occured. How...

02 July 2024 4,932 3 View

What is the reason of appearance of 2 or 3 peaks in zeta potential analysis of sample?

Hello I have prepared metal nanoparticles and did zeta potential. Normally there is a single peak in sample but now there are 3 peaks. I prepared sample for analysis first I prepared 10 mg/mL...

30 June 2024 1,063 4 View

EDS or EDX concetration finder?

Hello everyone, I'm facing an issue with EDS software that prevents me from obtaining atomic or weight percentages for my scan. However, I do have access to the raw data, which shows intensity vs....

29 June 2024 6,664 14 View

Could you please help me to match the XRD peaks of MoVO oxides?

Hi all, I have few XRD files of MoVO oxides. These are newly synthesized compounds. Can anyone suggest me, how can check my XRD files from database? I want to match my XRD peak to the database. Is...

24 June 2024 6,448 3 View

What does an increase in intensity mean in GIXRD?

When I examined the GIXRD data obtained recently, I observed that the sample treated with O2 plasma on the Cu surface deposited on Si chips showed increased intensity compared to the sample...

19 June 2024 6,900 5 View