Hello everyone, i'm running a model with apply faulting in base model in FLAC2D, but when Apply faulting, there come problems of "Bad geometry"?

20 July 2021 1 7K Report

i'm running a model with apply faulting in base model in FLAC2D, but when Apply faulting, there come problems of "Bad geometry". I would be grateful if you guided me through this.

Shirin Jahanmiri

With respect,

When creating a mesh, it is important to keep in mind that built zones may have incorrect geometry, and analysis tools may display a Bad Zone Geometry error if the length/width ratio is over a specific number. Therefore, In FLAC2D to ensure that the proper meshing is used, examine the model's length-to-width ratio.

Badges
Science topic

More Reza Sohrabzadeh's questions See All

If the emission of all greenhouse gases is stopped now, will the temperature of the earth continue to rise?

Here's a serious question: If we were to stop emitting all greenhouse gases right now, would the Earth's temperature start to cool down, or would the existing greenhouse gases continue to warm the...

30 July 2024 5,123 4 View

How to prepare 100ml solution of 2.5% Glutraldehyde in 0.1M PBS(phosphate buffer) pH about 7, from 25% Glutradehyde and 1X PBS?

final solution volume is 100ml

03 June 2024 417 0 View

How can i use hexamethyldisilazane(HMDS) for drying instead of Co2 and freez drying for SEM analysis of rice anther and pollen?

could you please help with a protocol? should i do it directly on the aluminium stub after dehydration with 100% alcohol or not? should i release the pollen or whole anther is better and dehisce...

03 June 2024 4,793 8 View

What is the best method to enhance the surface hardness of cutting tools made from SPK steel?

SPK tool steels are used for cutting wires made from low carbon steels. We are searching for a cheap and effective method for increasing the cutting characteristics of the cutters.

14 May 2024 4,948 0 View

Constant Reciprocal of Step Size?

Hello I recently encountered a problem with the reciprocal of step size plot in Comsol Multiphysics. After a certain time (seconds) in a time-dependent solver, the plot oscillations will be...

04 May 2024 7,278 0 View

Poor viability of T cell after transduction with CAR Lentivirus!?

Hi everyone I produced a batch of virus , enriched it with centrifugation, and titrated it with T cells after 48h. For my experiments I want to use MOI 3 and that's equal to 1/12 dilution. but at...

02 May 2024 9,727 3 View

Are you interested in submitting papers to a new journal called "InfoScience Trends"?

InfoScience Trends offers comprehensive scientific content that delves into various facets of information science research. This includes but is not limited to topics such as information...

26 April 2024 9,521 1 View

Does the color of pan traps affect the sampling of flies from the superfamily Bombylioidea?

Garret, 2020 used traps of blue, yellow, and white colors for sampling and collected several specimens.

06 April 2024 6,995 2 View

Laboratory procedures for identifying the concentrations of formic acid and acetic acid in aqueous solutions???

What are the laboratory procedures for identifying the concentrations of formic acid and acetic acid in aqueous solutions using titration, spectrophotometry, or gas chromatography methods...

06 April 2024 187 3 View

Is it possible to produce a very small amount of volatile oil along with condensed gas? If so, could you please provide a real example?

Is it possible to produce a very small amount of volatile oil along with condensed gas? If so, could you please provide a real example? Thank you.

04 April 2024 1,411 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

Is it true that there is a physico-statistical meaning to the constant π other than circular geometry but the iron guardians of the SE deny it?

We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...

22 July 2024 4,285 9 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

A new interesting geometry problem. Can you find the measure of angle?

In the isosceles triangle ABC (AC=AB), the angle at the vertex is 20°. Point D is chosen on the side AB such that AD=BC. Find the measure of angle CDB.

23 June 2024 7,541 8 View

The problem at hand concerns the application of the "II Lagrange's formula". Would you like to try solving it?

In triangle ABC, the bisector AL₁ is drawn. Points O₁, O₂, O are the centers of the circles circumscribed around triangles ACL₁, ABL₁, ABC, respectively. The radii are denoted as R₁, R₂, R for...

12 June 2024 7,596 1 View

How to create solid45 elements to an existing cad geometry?

I imported an 3D cad geometry in ansys. Now I want to create the mesh with solid45 element in workbench. How to proceed?

05 June 2024 2,490 1 View

A new interesting problem. Would you like to try solving it?

Consider a circle of radius R with center O. Two other circles are internally tangent to this circle and intersect at points A and B. Find the sum of the radii of the other two circles, given...

29 May 2024 9,788 1 View

Why does my IRC calculation generates higher energy structure around TS ?

While computing the mechanism of a trimethylsilylcyanation related to this work (10.1021/acs.organomet.1c00070) I managed to optimize the geometry of both reactants and product and locate a good...

26 May 2024 9,925 0 View