Hello everyone! can anyone explain my BET and BJH result? and why the result (lUPAC) does not match the default type? In this case, what can I do?

More Azim Rasulovich Abdullaev's questions See All

Can the dielectric constant be lower than 1?

I prepared a membrane for use as a dielectric material using the electrospinning method. their index is as follows: one shows 0.9 under 9 GHz and another 0.83 under 8.5 GHz but one shows 1.03 and...

11 April 2024 247 2 View

Is there anyone who can expand on the methods they employed to measure or assess the influence of peer interactions on sociolinguistic competence?

Observational Analysis: Researchers observe and record conversations to study how individuals from diverse linguistic backgrounds interact. Transcription: Spoken language is transcribed into...

10 October 2023 2,892 10 View

Is it possible to test variation in a DV for 2x2x2 design for 2 manipulated and 1 measured variable?

Is it possible to test a 2x2x2 design where the first two variables are manipulated high/low categories and the third variable is a measured continuous variable? Would it be suitable to convert...

27 September 2023 5,246 4 View

Integrated Reflective Surfaces for Free Space Optics?

In optical wireless communication, there are two main system architectures: • Intensity modulation and direct detection (IM/DD) • Coherent modulation/detection In IM/DD systems, the optical...

27 June 2023 7,275 1 View

How to access Scientific textbooks and explanations?

Hello. I was about to study a Killifish genome and basically how it works, it's main mechanisms. However, whenever I search for it on Google or Google scholar, I get only scientific papers, which...

22 June 2022 2,007 0 View

How to calculate Smix (Surfactant mixture) molar ration in combination with oil phase?

Briefly, the question is about the calculation of the molar ratios of Smix i.e. surfactant mixture and the oil phase ranging from 1:9 to 9:1 to get an optimized formulation. 1. the surfactant...

16 April 2022 2,724 1 View

Any one know how to solve with my ETAP 12.6?

I am using ETAP power station 12.6 Enterprise version, and I want to try GIS module, and it shows this comment: " ESRI GIS system not installed! ETAP GIS functionality can't work without ESRI GIS...

26 October 2020 9,996 2 View

Did you get any issue in culturing Methylomonas methanica ?

I have just begun to cultivate M.methanica 25384 as pure culture. I transferred the culture ordered from DSMZ into the medium 1313 as suggested. The strain grew differently among the triplicates,...

19 October 2020 4,007 1 View

How do you select the potential for corrosion test?

I'm doing potentiodynamic test. In my experiment, I used 316L stainless steel with exposed area 9.2cm^2. I'm a bit confused what to insert the initial and final potential.

09 March 2020 860 3 View

Interested to make a collaboration?

The native to South American Stevia plant that has been used as a sweetener for hundreds of years. Today, zero-calorie stevia, as high-purity stevia leaf extract, is being used globally to reduce...

23 April 2019 5,553 3 View

How to increase citation in Research Gate?

How to enhanced h-index in Research Gate?

04 August 2024 3,368 4 View

H-index issues?

Hi Sir/Madam, I would like to know why my h-index is stuck to 15 despite the number of new publications added. Could you explain me how marks are granted. Best, Daniel

28 July 2024 2,607 2 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

How can the rubber fibres produced by the electrospinning device be removed from the fibre collect(aluminium foil) ?

How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...

26 July 2024 8,281 0 View

BD Cell Viability Kit - TO evaporation?

Hello, I'm conducting flow cytometry experiments using the BD Cell Viability Kit and I've noticed that the TO solution ends much faster than the PI solution. I store the solutions according to...

22 July 2024 2,257 0 View

What is the degassing temperature and time for biochar for BET surface area analysis if TGA is not possible?

Since BET and TGA both are very costly instruments and many places the facilities are not available (for large number of samples) hence a threshold degassing temperature and time is preferable

16 July 2024 8,112 2 View

What is Printed Circuit Board (PCBs)?

Dear Members, We are conducting a research survey on the Printed Circuit Board (PCBs) industry and would greatly appreciate your valuable input. To participate, click the following...

09 July 2024 4,936 1 View

Refractive index in the W-band (75-110 GHz) of some material (Teflon - PTFE) ?

08 July 2024 9,140 1 View

Why does a nitrogen adsorption-desorption isotherm form two loops?

BET analysis

27 June 2024 6,964 1 View

Why PLLA deposited by gap electrospinning lose piezoelectricity?

I tried to prepare aligned PLLA nanofibers by gap electrospinning method. But after the deposition, when I tried to measure its piezoelectric sensitivity, it actually did not exhibit any...

17 June 2024 9,763 0 View

Alvena Shahid

Azim Rasulovich Abdullaev The adsorption isotherms appear to be type IV isotherms, which are characteristic of mesoporous materials. Mesoporous materials have pores that are 2-50 nanometers in diameter.

Azim Rasulovich Abdullaev

Alvena Shahid Thank you very much for taking the time to reply

Azim Rasulovich Abdullaev Thank you for your acknowledgment. I'm here to help anytime.