Geany #IDE #Fortran #Help With programming?

More Inaam Qazi's questions See All

Excessive distortion issue while doing non linear static analysis?

I am doing a non linear analysis incorporating material and geometric non linearity. I apply a non linear ststic load higher than the linear eigen buckling load. the analysis terminates on account...

03 April 2019 3,039 3 View

Differences in Load controlled and displacement controlled conditions ?

Why is that load controlled and displacement controlled boundary conditions give different results for same meshing and boundary restraints ? I specify time at the end of load step as 1 and no of...

01 February 2019 6,263 7 View

Selection of node from a subset of nodes corresponding to maximum displacement in one direction?

How to select a node from a set of selected nodes and get the node number corresponding to maximum value of say y displacement. It should also take the mod (for selection of maximum negative...

31 December 2018 5,146 1 View

How to do linear combination of eigen modes corresponding to 2 different loadings in APDL?

If I apply 2 different types of loading and I get different eigen modes for different loading types, how do I combine them in a linear fashion in APDL.Tutorial would be nice.I have used upgeom...

10 November 2018 3,707 0 View

How to get APDL to read a column from a matrix element by element , so that I can operate on each elements ?

I have made a matrix of areas 76 *5 which contain areas in first column , centroidal coordinates in the 2,3,4 columns.I want to read the first column element by element so that I can make...

07 August 2018 3,173 6 View

Force driven load deflection response in apdl?

How to get a post buckling deflection curve using force driven analysis in apdl. The graph stops short and the run is terminated when the load reaches ultimate load or when the von mises stress...

06 July 2018 8,671 0 View

How to SELECT THE keypoints associated with area numbers in APDL?

I have selected a subset of areas by ASEL,S,LOC,Y,0 APLOT With the selected areas I have counted them via *GET,A,AREA,,COUNT then I have defined an array via *DIM,B,ARRAY,1,AREA This creates an...

06 July 2018 8,320 4 View

Doubts in representative finite element modelling?

I have attached a picture which shows 2 co axial tubes being compressed by heavy end plates. But the reduced modelling technique does not make much sense to me . IF someone could help in...

03 April 2018 8,962 3 View

Modelling issues with flange buckling of I beams ?

I am doing non linear buckling analysis to determine the buckling co efficient of flange buckling of I beam. For doing eigen value buckling analysis , and from there I do non linear analysis to...

02 March 2018 4,655 1 View

How to add residual stress distribution ?

I am modelling an I-beam with geometric imperfection and residual stress distribution for non-linear analysis. How can I add residual stress distribution which is varying in nature. Please find...

02 March 2018 6,530 7 View

Can NFL theorem be valid in infinite search space in ML?

NFL theorem is valid for algorithms training in fixed training set. However, the general characteristic of algorithms in expanded or open dataset has not been proved yet. Could you show your...

01 March 2021 1,189 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to address this issue in the analysis of Real-Time PCR results?

To dear Researchers, I was analyzing a series of concentration for estimation of Real-Time PCR efficiency. The concentration was 1:10. I used MS-excel to evaluate Slope. The result of slope was -8...

01 March 2021 8,683 4 View

Can I download BibExcel for MacOs?

Hi everyone, I would like to ask how I can download BibExcel software for MacOs? There are some links which are supported by Windows but I could not find it for Mac. or is there any other software...

01 March 2021 652 1 View

How can I represent SDS-PAGE results for machine learning analysis?

I am trying to classify and analyze the results of an SDS-PAGE based array for bacterial detection using machine learning, but I have trouble finding the best way to represent the results with...

27 February 2021 9,176 3 View

Is there an open source free software for text mining and sentiment analysis?

I am looking for a free software for text mining and sentiment analysis for my research on customer review mining (it involves calculating polarity of attributes,opinion oriented information...

25 February 2021 1,920 6 View

Suggest me some trending topics for phd research in text mining/AI/machine learning?

My master's research is in info retrieval and text mining. I would be grateful if you could help me to select a good topic for my phd research proposal.

24 February 2021 393 14 View

Anyone with some Transgenomic Wavemaker software? Seeking help from the chromatography community?

I am trying to seek out some Transgenomic Wavemaker software (happy to purchase a computer too) to operate a fraction collector. The only way to connect to the fraction collector so far is to...

23 February 2021 9,181 1 View

Best excel chart to compare algorithms' running time?

Hi I want to compare the running time of robotic path planning algorithms. The grid size is 8X8. I have 100 scenarios of start and goal positions.. Each scenario is run in three obstacles ratio...

22 February 2021 621 1 View

How do I add a udf to Ansys fluent and does it need to be compiled before hand ?

I have a Define_CG_Motion udf written in c where do I add it to my Ansys fluent project and does it need to be compiled before that?

21 February 2021 9,347 3 View

Chemseddine Chohra

Since it does not even compile, are you sure that you have a Fortran compiler installed ? because Geany is just an editor and not a compiler as you said.

Inaam Qazi

Yea I have code blocks installed and that is working when i run the same code in there. while compiling and building it shows "16:52:07: Process failed (The system cannot find the file specified)" . Please find the attached file for executing error