For elastomers I am not able to operate it at low voltages it requires very high voltage(2000v) for operation.Can anyone explain why i am facing this?

More Sumeet Shekhar's questions See All

Can anyone provide articles related to TAM model adopted with the mobile payment or technology adoption ?

Hi all Can anyone give me some research papers which have shown behavioral a behvaioural intention leads to actual uses i.e. adopted full TAM model in the context of mobile wallet, mobile...

30 December 2020 7,221 4 View

What are the applications of inverse filter?

Electronic inverse filters are usually used to compensate for the effect of unwanted environmental filtering of signals. What are the other possible applications?

28 December 2020 5,904 3 View

Does copying and pasting from own paper in PhD thesis is considered as plagiarism?

Copying and pasting from own paper in a PhD thesis is acceptable or not?

03 December 2020 5,639 14 View

What kind of possible device mismatch we can expect while designing circuits with Current Mode Analog Building Blocks?How these mismatches affect THD?

Large values of resistors and capacitors are hard to match in the fabrication phase. It will create some systematic mismatches. So how to avoid those kinds of mismatches in case of current-mode...

19 November 2020 3,709 8 View

How to add Stanford University CNTFET Model in OrCAD PSpice?

The HSPICE and Verilog versions are available here https://nano.stanford.edu/stanford-cnfet-model. Is it possible to add CNTFET model in OrCAD Pspice and if yes, what are the steps regarding this.

12 October 2020 916 2 View

How to plot an Isopleths connect points or contours figure on diet data of animal?

I want to prepare like following example figure for Indian fox diet data. But I don't how to prepare it. I have % relative frequency and % volume data. Does anybody help me how to prepare it? The...

21 August 2020 6,215 4 View

How to interpret the negative slope coefficient in regression Analysis?

I performed a linear regression, in which I got a negative slope coefficient. May I interpret as if the explanatory variable increases, then the response variable decreases?

01 August 2020 739 11 View

Can a person improve his speaking skills in a language with peers of same level of expertise in language?

If a person who is good in reading, writing and listening to a language but has not much practice of speaking, can he improve by practising speaking with people of the same level?

03 May 2020 8,382 39 View

How to avoid overlapping labels in an R plot?

Hello Everyone, I want to produce the following figure using R for my paper. But I don't how to produce this figure without overlapping labels in R. Does anybody help how to do that in plot...

18 March 2020 6,517 4 View

I am facing in post processing of analysis of muffler on Ansys. How should I ensure that my muffler is not producing more then 110 db of sound ?

I am designing a muffler for my fsae car and I'm using KTM 390 engine. I did a flow analysis on muffler on ansys and plotted a transmission loss plot. But I don't know how to interpret it as I...

04 February 2020 6,713 1 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

How to clean up TEM grid with plasma cleaner?

I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...

23 February 2021 3,262 5 View

What are some underexplored theories and concepts in Activated Carbon as A Water Filter?

Hi, me and my team mates are currently planning to pursue the topic of Activated Carbon from Coconut as a Water Filter. And we would like to ask for your suggestions and knowledge on what specific...

22 February 2021 6,569 3 View

Asit Baran Samui

As explained by Dr. Tihomir, the elastomers normally operate at high voltage. If blended with conducting fillers, such as metal particles, conducting polymers, conducting carbon black, the voltage requirement can be reduced.

Hisay Lama

The elastomers are typically insulators, thus its operating voltage is very high. In order to decease the operating voltage you can try with the method mentioned by Prof. Asit Baran Samui