Water flows in a curved channel in which either outer or inner wall has const heat flux while others are insulated. Will 'h' be same in the two cases?

21 July 2023 0 6K Report

Water flows in a curved channel in which one wall has constant heat flux boundary condition while others are insulated. In case 1, outer wall has heat flux condition while in case 2, inner wall has boundary condition. Will the heat transfer be same for the two cases or different. Buoyancy is neglected.

Badges
Science topic

Similar topics
Physical Sciences
Waves

More Kinshuk Shekhar's questions See All

Can anyone provide articles related to TAM model adopted with the mobile payment or technology adoption ?

Hi all Can anyone give me some research papers which have shown behavioral a behvaioural intention leads to actual uses i.e. adopted full TAM model in the context of mobile wallet, mobile...

30 December 2020 7,221 4 View

What are the applications of inverse filter?

Electronic inverse filters are usually used to compensate for the effect of unwanted environmental filtering of signals. What are the other possible applications?

28 December 2020 5,904 3 View

Does copying and pasting from own paper in PhD thesis is considered as plagiarism?

Copying and pasting from own paper in a PhD thesis is acceptable or not?

03 December 2020 5,639 14 View

What kind of possible device mismatch we can expect while designing circuits with Current Mode Analog Building Blocks?How these mismatches affect THD?

Large values of resistors and capacitors are hard to match in the fabrication phase. It will create some systematic mismatches. So how to avoid those kinds of mismatches in case of current-mode...

19 November 2020 3,709 8 View

How to add Stanford University CNTFET Model in OrCAD PSpice?

The HSPICE and Verilog versions are available here https://nano.stanford.edu/stanford-cnfet-model. Is it possible to add CNTFET model in OrCAD Pspice and if yes, what are the steps regarding this.

12 October 2020 916 2 View

How to plot an Isopleths connect points or contours figure on diet data of animal?

I want to prepare like following example figure for Indian fox diet data. But I don't how to prepare it. I have % relative frequency and % volume data. Does anybody help me how to prepare it? The...

21 August 2020 6,215 4 View

How to interpret the negative slope coefficient in regression Analysis?

I performed a linear regression, in which I got a negative slope coefficient. May I interpret as if the explanatory variable increases, then the response variable decreases?

01 August 2020 739 11 View

Can a person improve his speaking skills in a language with peers of same level of expertise in language?

If a person who is good in reading, writing and listening to a language but has not much practice of speaking, can he improve by practising speaking with people of the same level?

03 May 2020 8,382 39 View

How to avoid overlapping labels in an R plot?

Hello Everyone, I want to produce the following figure using R for my paper. But I don't how to produce this figure without overlapping labels in R. Does anybody help how to do that in plot...

18 March 2020 6,517 4 View

I am facing in post processing of analysis of muffler on Ansys. How should I ensure that my muffler is not producing more then 110 db of sound ?

I am designing a muffler for my fsae car and I'm using KTM 390 engine. I did a flow analysis on muffler on ansys and plotted a transmission loss plot. But I don't know how to interpret it as I...

04 February 2020 6,713 1 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View