Hello:
Could someone please tell me if there is a standard output variable via which you can get values of the fluid pressure inside the fracture in Abaqus?
Please and thank you,
Mousumi
Dear mousumi,
You can find "por" in visulization module for the above issue.
Good Luck
Hello: I am doing my research in proppant transport in pkn type fracture networks. I have modeled the fractures with 3D cohesive elements in Abaqus, and I have labelled certain nodes to be the...
31 December 2018 5,212 0 View
Hello all: I have been working on proppant transport inside fractures for quite some time now. And now, I have a question regarding meshing technique when it comes to three or four or five...
09 October 2018 9,325 0 View
Hi: All I know is that if you go into more depth from Hooke's law into plane stress or plane strain conditions, the inverse of the material stiffness matrix is the material compliance! However,...
09 October 2018 3,386 3 View
Hello: I work with Abaqus CAE/Standard a lot! Whenever I have tried to put the number below the *Depvar keyword to be greater than 15 (and there can be any subroutines (UMAT or USDFLD) with no...
08 September 2018 9,471 3 View
Hello: I have been working on proppant transport and hydraulic fracturing in Abaqus for very long, but so far I have only dealt with 2D models, with z-direction being absent. Although, I have...
06 July 2018 6,825 1 View
Hello: I work in Abaqus 2017 a lot. I have noticed that when I submit any abaqus job (that does not contain any subroutine!) via parallel processing (aka cpus=4 or 8), it runs just fine! But,...
03 April 2018 168 2 View
Hello: I am modelling for 2D hydraulic fracturing in Abaqus Standard, and adding proppant transport simulation to the this as well. I have three steps to my model. Geostatic Step2 (where I...
03 April 2018 4,081 5 View
Hello: I am trying to do a very simple thing that I just can't seem to do in Abaqus! I know how to create a new text file and write to it any output variables with any desired format I want!...
02 March 2018 4,554 3 View
Hello: I have a very unique problem here with Abaqus Standard! I have a very slim fracture in which I am trying to simulate proppant transport, and the this very narrow fracture is embedded...
02 March 2018 6,801 1 View
Hello: Could anyone tell me how do get an XY plot in Abaqus CAE where the x-axis is x-coord (or element number) and the y-axis is the output variables of interest, such SDV or flowrate,...
02 March 2018 8,598 3 View
I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...
01 March 2021 10,078 1 View
I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...
01 March 2021 6,661 3 View
I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...
01 March 2021 736 3 View
Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...
01 March 2021 9,511 3 View
Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...
28 February 2021 3,442 2 View
I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...
28 February 2021 4,841 3 View
I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...
28 February 2021 5,415 1 View
I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...
27 February 2021 6,818 3 View
Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...
25 February 2021 9,936 2 View
I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...
24 February 2021 4,908 5 View