How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How can I find a Raman spectrum wavenumber corresponding to what compound?

I have several Raman spectra with very distinct peaks at certain wavenumbers, such as 277, 359, 466, 583, 623, 686, and 795cm-1. How can I identify them to what compound(s)? The RRUFF and others...

24 February 2021 363 3 View

Is there a suitable way to confine cell attachment area inside a multi-well plate?

Are there any types of cylindrical cell culture inserts that are designed to confine cell seeding area? Say, if I'm using a 12 well plate (3.5 cm^2/well), but only want to seed cells in the middle...

22 February 2021 7,127 4 View

Does anyone know if the Quantstudio 3 qPCR machine requires a passive reference when Using SYBR? I ran a qPCR and got the plot in the attached file.?

I know that my target is in my sample as I extracted it from cell culture myself. These plots show some amplification. The first one seems O.K for the first 36 cycles but then collapses at the...

14 February 2021 2,809 2 View

NVT or NPT is preferable for gas adsorption simulation ?

Hi there, In order to perform molecule dynamic simulation on gas adsorption on substrate materials, NVT or NPT ensemble is preferable ? Thanks!

08 February 2021 173 1 View

Ferret PBMC Fc block?

Hi all, I'm going to run Flow Cytometery on ferret PBMCs but can't find an Fc block for ferret PBMCs. Does that even exist? Do I need ferret-specific Fc blocking antibodies or can I use:...

18 January 2021 4,504 5 View

Option "cutoff-scheme" not recognized by Gromacs 4.6.5?

Hi, I got the following error message while running parallelized simulations with OpenMP: OpenMP threads have been requested with cut-off scheme Group, but these are only supported with cut-off...

02 January 2021 4,564 5 View

Can I use gelatin to pre-coat the plate for HepG2?

I am working with HepG2 cells, and I want to pre-coat my flask/plate to keep the cells in single layer. Can I use gelatin to coat the dish or I need to use collagen? I was wondering if any of you...

15 December 2020 5,599 3 View

Did anyone do microglia Oil Red O staining?

I need to stain adiposome in microglia, but I don't know how to confirm that are really success? method : Removed media and washed cells with PBS, then added 4 % paraformaldehyde for 20 minutes at...

24 November 2020 2,359 2 View

How to calculate UTCI using ERA5 dataset?

17 November 2020 2,127 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to address this issue in the analysis of Real-Time PCR results?

To dear Researchers, I was analyzing a series of concentration for estimation of Real-Time PCR efficiency. The concentration was 1:10. I used MS-excel to evaluate Slope. The result of slope was -8...

01 March 2021 8,683 4 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View