How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

What test should I use to compare two or three means, if data is not normally distributed but sample size is > 30 in each group?

I personally feel this as a most confusing question. As per my understanding, if sample size is > 30, and sample is skewed, we can still use paramteric approach, as it will follow Z...

01 March 2021 1,587 6 View

How to calculate Ligand-active site distance in a ligand-protein complex from MD simulation?

I have run a MD simulation of a ligand-protein complex in GROMACS using CHARMM forcefield. Reviewer has asked me to calculate Ligand-activesite distance and binding free energy of ligand with...

27 February 2021 4,703 1 View

Efficiency of Proximity Feed Patch Antenna ?

Greetings to all of You! I have searched some research papers for the designing of a proximity coupled patch antenna. Researchers are talking about the impedance bandwidth of the antenna but...

24 February 2021 7,662 3 View

Please help in identification of this insect?

This insect is minute in size around 1 mm and not clearly visible with naked eye.

22 February 2021 5,907 11 View

What should a smart water system look like?

Our team is designing a smart water C&C dashboard for a smart city initiative. As we look into the current smart water system landscape, we couldn't reconcile to a definitive solution that...

16 February 2021 1,094 3 View

What is causing the raw fluorescence to be negative?

Hi everyone, I would really appreciate it if someone can tell me when and why a raw fluorescence starts below zero. In the picture attached below the blue colour curve starts from a negative...

09 February 2021 4,642 3 View

How to match the XRD of a compound for which there is no JCPDS file ? Is there any other characterization to claim the synthesis of desired compound?

I have synthesized LiMgF3 using the starting precursors LiF and MgF2 via solid state diffusion method. Now I am looking for some characterization to claim the desired product, as there is no...

09 February 2021 921 3 View

Can anyone suggest me broad host range fluorescence expression vectors for Gram-positive bacteria ?

Hi everyone, I am looking for fluorescence expression vectors for expression in gram-positive bacteria present in the skin microbiome. I need to tag them with a fluorescence marker and observe...

06 February 2021 2,566 4 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to approach CFD simulation results of a flow past a cylinder?

Hi all, I'm doing a transient simulation of flow past a rectangular cylinder close to the free surface. As far as I'm concerned, the common practice is to discard the initial stages of the...

25 February 2021 1,348 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View

Model Volume fraction and magnetic field applications of nanofluids in ANSYS?

Hi I am working recently on a project where I have to study how the thermal properties or heat transfer enhancement of nanofluids as the volume fraction changes, or if a magnetic field is applied...

22 February 2021 961 2 View

How to model static fluids in ANSYS?

Hi I was wondering if there is a way of simulating static fluids (including brownian motion) of nanofluids in ANSYS. I am currently working on a theroretical based project where I am trying to...

20 February 2021 776 1 View

How to overcome convergence issues in concrete arch models?

Hi, I have modelled a three-span arch bridge with soil fill over along with pedestals. The FE modelling is done in LUSAS with HX8M solid elements (i.e. 3D solid modelling). The non-linearity is...

20 February 2021 1,346 2 View

Comsol Maximum number of Newton iterations reached?

Comsol is investigating deformation due to gravity. Gravity is applied to the nanosheets to check for displacement and stress. If I input the Young's modulus of the channel to about 1 [GPa], the...

15 February 2021 6,027 3 View

Why is my vc-relax computation of a W-based material is not converging? What important factors should I consider to attain convergence?

Here are some of the parts of the input file: &system ibrav = 0, nat= 9, ntyp= 2, ecutwfc = 36.7, ecutrho = 367, smearing = 'methfessel-paxton', occupations = 'smearing',...

10 February 2021 4,689 1 View