Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

What is the difference between PBE and PBEsol functional?

Hello, I am a 3rd year chemistry student and I'm writing my project report on computational chemistry. does anyone know how PBEsol improves upon the PBE functional? Thanks in advance

19 February 2021 7,068 4 View

Can someone help me with this error that I am getting while estimating a VAR model in R?

I am using annual time series data to estimate a VAR model in R. However, when I run the command to find the optimal lag length, I get the following error: Fehler in VARselect(data, lag.max = 10,...

18 February 2021 9,647 3 View

What is the method of removing RNase contamination from a filter paper surface?

I am working on a biosensing project on paper substrate, however, it is found that the RNase contamination occurs on the filter paper. Might I ask is there any method to clean the paper surface...

12 February 2021 3,926 3 View

In your experience what is the difference between G.652D and G.655D optical fiber. In field and in lab?

In our current era there is a big confusion about the usage of G.652 and G.655 optical fiber cable. Theoretically G.655 is much better than G.652 but the operator feel that G.652 is giving almost...

11 February 2021 4,006 8 View

How many dilutions are good enough for TCOD50 of SARS-CoV-2?

I started with 10e-1 till 10e-10. But when I searched for online calculator they mostly consider 5 dilutions. Is there a reason behind it or I should make less dilutions?

11 February 2021 5,839 3 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

Bought HUVEC from Invitrgen.need to revive it.expected it is cryofreezed in DMSO.Do I need to remove the DMSO for plating the cell for the 1st time?

After I cryofreeze the cell do I need to remove the DMSO for culturing the cell for next passages .

28 February 2021 7,738 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

Do you kow of any database containing data on retention time, log P and polarizability for a large number of molecules?

Hi, I am a chemistry undergraduate doing my dissertation project on HPLC. In my project, I need to predict the HPLC retention time of 20 aromatic molecules, the calibration set. To do this I will...

24 February 2021 2,602 1 View

How to seperate PEG-4000 from aqueuse phase ?

Hello everyone , Please tell me if It possible to seperat POlyethelyn glycol -4000 from an aqueuse media by other ways rather heating . I have tried salting out by electrolyte solution to...

22 February 2021 7,285 5 View

How to dilute Toxin-DMSO solution?

I have a concentrated solution of a toxin(50 micromolar) in DMSO 100%. I need to dilute it inorder to dilute both the toxin and DMSO wich can be toxic to cells. Which would you guys recommend to...

19 February 2021 7,447 2 View

How to successfully revive cells stored at -80 degree C for a year?

I am working on C6 cells along with other neuronal cell lines. We have preserved the cells in 90%FBS and 10% DMSO solution. We are reviving the cells after a year and cells are either not binding...

18 February 2021 4,499 1 View

How to analyse monosaccharide compositions from soluble fiber?

I have tried to hydrolyze the sample using 2 M TFA at 100C for 24, 48 h and 120C for 2 h. From these conditions, the HPLC results showed that peaks were not separated into monosaccharide. I found...

17 February 2021 5,230 1 View