Effective method to prevent oxidation of powder during mechanical alloying?

More Refaie Omar's questions See All

Why does flow deformation occur at the test line and control line on nitrocellulose membranes (LFIA)?

I use 1% BSA in 10 mM phosphate buffer (pH 7.4) solution when striping my nitrocellulose membranes with antigens and antibodies. However, I always observe deformed flow when my sample or running...

16 February 2021 4,224 3 View

How can I set up UV irradiation for crosslinking lab?

Hi, I am using a mix of 2 polymers and want to try and crosslink them. I have a UVA lamp of 365nm and have tried the lab previously at 30cm above. How would you recommend I approach the lab and...

31 January 2021 8,711 3 View

Which air pollution/air quality books do you recommend for working with environmental engineering students?

I am exploring up-to-date books on air pollution and air quality, and I would like to know which books do you recommend for environmental engineering students.

25 January 2021 3,972 7 View

How to simulate Sloshing water using Dynamic mesh in ANSYS Fluent ?

I am trying to model sloshing water in a tank in ANSYS Fluent using Wall motion. BUT it seems that System coupling is not responding to wall motion and it works only with Dynamic mesh.

20 January 2021 2,963 3 View

Are there other models that meet the same purpose?

Both Jakes and Gaussian models are used to characterize the power spectral densities of mobile communication channels.

11 January 2021 759 3 View

SDAS, secondary dendritic arms space relation with solidification rate?

Want to know the relation between sdas and solidification rate, the mechanism by which getting smaller space between secondary arms by increasing the rate ?

23 December 2020 735 2 View

Shall i use the country's CPI score or rank while entering the data ?

I have the Corruption perception index as a control variable in my study and i'm not sure what i have use the score or the rank of the country ? please advice what i have to use in the data entry...

09 December 2020 3,797 2 View

Any thoughts for a research topic in a master's level thesis regarding combination of Supply chain and entrepreneurship?

Hi, we are two master's students at JIBS and currently looking for inspiration and suggestions for a research topic that has a connection of both "supply chain" and "entrepreneurship". maybe...

18 November 2020 2,524 3 View

Can electrophoretic mobility measurements of polymer-coated AuNPs be used to infer the role of charge (if any) in their dispersion stability?

Hello Everyone, We have stable citrate-coated AuNPs dispersed in water. Different polymeric protective coatings (PEG, PVP, BSA) have been chemically grafted to the citrate-coated AuNPs for...

17 November 2020 2,903 16 View

How can instructors assess the intercultural competence of their ESL students?

Intercultural competence is a skill rarely taught and measured in ESL venues. What is an ideal way of measuring the student's progress in developing intercultrual awareness and testing it?

08 November 2020 2,176 16 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

Reza Askarnia

Article Fabrication of high strength aluminum-graphene oxide (GO) co...

You use ethanol solution for ball mill...Every 20 minutes ball mill, 10 minutes stop

Safwan al-qawabah

https://spj.sciencemag.org/journals/research/2019/4219812/

Chen Ding

Vacuum or add argon for protection

Manzar Iqbal

https://doi.org/10.1016/S0079-6425(99)00010-9

B. Srikanth Ragunath

Using Ethanol, Isopropanol, or Hexane as a dispersant can help to reduce the oxidation of metallic powders. If possible the powders can be milled in an inert atmosphere (Argon or Nitrogen)