14 November 2016 3 9K Report

does anyone have any good reference in ecological economic modelling for environmental impacts assessing?

I want to model the environmental impact of system of  (dairy farm+land).

More Kamran Noori's questions See All
What's wrong with my PCR products?

Hi , I have run my PCR products on gel electrophoresis, but I have seen excessive smear , do you have any suggestions for that?

08 June 2024 6,774 7 View

Please determine a suitable dimension for a wave channel to fit within a lab space of 16 meters by 5 meters；how about 12 meters long, 0.8 meters wide?

Hello everyone. I need a wave cahnnel for offshore wind turbine design. Can hydraulics experts help me in designing the wave channel with quotations links?

05 May 2024 6,867 2 View

Do you struggle with low DNA yield after extraction?

Molpure's SorbElut DNA extraction columns tackle the challenge of low yield. We're interested in collaborating – is there a potential fit for your research?

25 March 2024 6,622 0 View

How to prevent preliminary dilation of stress paths in loose sand samples shearing under undrained triaxial soil compression (CU) condition?

We have sheared numerous loose samples of sandy soils in undrained TXC conditions. A common behavior observed herein was dilatancy in stress paths at the first stages of shearing. Normally, it's...

16 December 2023 1,931 1 View

How to clean the container contaminated with DNA Green Viewer? Is this substance destroyed by autoclaving?

Can jars contaminated with DNA Green Viewer gel be washed? Is DNA Green Viewer safe to autoclave? Or are these containers considered hazardous waste?

29 September 2023 1,827 1 View

Request for guidance on protonation of ligand in MD simulation in gromacs and generation of correct gro file?

I hope this message finds you well. I am currently working on a research project focused on MD simulation study of drug desorption behavior on a boron nitride nanosheet with a non-covalent polymer...

28 September 2023 4,514 0 View

How to obtain correct topology of a system in which a polymer is covalently functionalized with nanosheet?

I am writing to seek assistance on a matter related to n2t file generation. I am using GROMACS and charmm36 force field in my work. I am covalently attaching a short polymer(poly-peptide) to a...

30 August 2023 8,023 2 View

How to obtain topology of a system in which a polymer is covalently functionalized with nanosheet/nanotube?

Dear research gate community, I am trying to simulate a boron nitride nanosheet covalently functionalized with a short chain polymer using charmm36 force field in gromacs. I obtained the str file...

19 August 2023 6,244 1 View

How to perform MD simulation on boron nitride nanosheet on GROMACS using charmm force field and how to create appropriate.n2t file?

I am reaching out to seek guidance and assistance regarding a challenge I've encountered while attempting to simulate boron nitride nanosheets using the CHARMM force field, specifically CHARMM36....

11 August 2023 7,922 2 View

I am looking for irradiance data of Photovoltaic Integrated Vehicle or Solar Vehicles. Can someone provide with some data?

Hi Guys, I m working on Solar Vehicles or Photovoltaic Integrated Vehicles. I need data of irradiance profiles. If someone has data or has any lead to where I can get it, I'd highly appreciate it.

23 June 2023 7,204 0 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Determining the worth of a point improvement in Hamilton Depression Scale?

Dear readers, Thanks for your attention. I am wondering about the health economic problem of quantifying the value of interventions which a) prevent, b) improve symptom profile and c) ultimately...

05 August 2024 3,246 1 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close