Easy to use freeware about air quality

Javier Rodrigo-Ilarri @Javier_Rodrigo-Ilarri

09 September 2014 0 6K Report

Do you know any easy to use freeware about air quality modeling??

Badges
Science topic

Similar topics
Engineering
Modeling

More Javier Rodrigo-Ilarri's questions See All

Which environmental problems arise from landfill mining ?

Landfill mining techniques arise as one of the available alternatives to mitigate negative environmental impacts from municipal solid waste landfills. High recycling potential generation is one of...

28 March 2020 2,019 10 View

Which freeware model model do you recommend for a detail analysis of soil contamination by pesticides ???

Pesticide application has currently been identified as one of the most relevant soil contamination sources. However, some more effort should be done to understand the fate and transport of...

10 November 2017 9,043 3 View

Do you know any easy to use freeware about light pollution modeling (LPM)?

Easy to use freeware about light pollution modeling (LPM).

08 September 2014 7,724 3 View

Environmental Impact Assessment models

Do you know any EIA freeware/software to be used for the assessment of hydraulic & environmental engineering projects???

08 September 2014 5,750 2 View

Easy to use freeware about noise modeling

Do you know any easy to use freeware about noise modeling??

08 September 2014 7,635 0 View

Which one to use, MODFLOW or FEFLOW?

Can you share your experiences about using both models for groundwater?

08 September 2014 2,906 14 View

E-learning, online courses and webinars in groundwater and environmental problems?

What is your opinion about e-learning, online courses and webinars in groundwater and environmental problems? Are they worthy? Any suggestions?

08 September 2014 5,594 4 View

How can geotechnical parameters of solid waste be determined?

In order to analyse slope stability on solid waste landfills, geotechnical parameters of waste must be estimated. Which lab analysis could be used? If no lab analysis are available, which values...

04 August 2014 6,119 4 View

Can anyone help with alternatives to RBCA risk assessment model?

Do you know any software which could be an alternative to the RBCA software toolkit for chemical releases to perform risk assessment evaluations?

27 July 2014 8,890 3 View

Is it worthy to develop new iOS, Android and browser software for solid waste management infrastructures design?

Is it worthy to develop a full new comprehensive software tool for solid waste management infrastructures design? I am considering doing so with a set of colleagues but it will definitely take...

27 July 2014 6,681 6 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Are air moisture harvesting technologies effective in combating desertification?

Air moisture harvesting Air water collection devices

06 August 2024 5,473 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View