How to incorporate a variable in damage model?

15 December 2020 7,284 2 View

Question regarding Primer Designing in qPCR?

Hi Everybody I have not done qPCR, and try to figure out the steps of that. From this regard, I am wondering Should primers designed for mRNA sequence or any other (cDNA, DNA, RNA) in qPCR, if...

07 December 2020 2,203 9 View

Mathematical or computational modelling of protein oxidation?

I am looking for a research paper about the mathematical or computational modelling of protein oxidation (caused by reactive oxygen species).. I would really appreciate that if someone helps me...

17 November 2020 2,340 3 View

Is it possible to still allow me to edit my article?

I made two errors in the references when modifying my article proof. Then I immediately informed the journal. But they prepared the article for publication. And published on the journal site.Is it...

16 November 2020 8,273 6 View

Can FEM model learn from experimental results?

I am looking for a research in which the finite element model was trained based on experimental results.

02 October 2020 9,277 19 View

DLS: How to convert Number%,Intensity% and Volume% to q3,q6 or q0 distributions?

Hello, I am using a Malvern ZetaSizer for my work and as a result in this device, it is possible to get PSD based on Intensity%, Number%, and Volume%. My question is how to convert each of these...

14 September 2020 1,399 4 View

How can I access the Seqscape software 2.7 ?

Hi, I need Seqscape software 2.7 to analyze DNA sequences because this version supports 3500 sequencers. Please help me how can I access this version of the software? Thanks

17 August 2020 4,693 3 View

Why does stresses evolve in only one element in Abaqus explicit?

I am trying to run my VUMAT code with a model in Abaqus/explicit. After that the run has been completed, I observed that the stresses have been evolved in only one element as shown in the attached...

27 May 2020 5,506 3 View

How to do baseline correction for DSC test data?

I have some raw DSC test data and I need to do baseline correction. I don't know how should I do it. I would appreciate it if someone can help me with this.

16 May 2020 8,273 7 View

Problem with nonlinear curve fitting?

Hello all, Actually, I am dealing with an issue that I can't get desirable results out of my curve-fitting problem. I used lsqcurvefit in the first place. Then, I added MultiStart to my code as...

30 April 2020 4,943 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View