30 September 2023 1 4K Report

design of the photonic crystal lattice

More Miami Mohammed's questions See All
What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

Can anyone suggest a topic for the Impact of AI and ML in the financial institutions?

I am currently doing my Master Thesis in FinTech and I am thinking of doing my project on the impact of AI and ML on the financial industry but as the impact of these technologies on the industry...

21 February 2021 7,128 3 View

Where I can find materials to learn Fuzzy VIKOR methodology?

Please suggest ways to learn Fuzzy VIKOR methodology in a best possible way. And is there any toolkit available for the same? Thank you in advance.

20 February 2021 8,271 3 View

What cause the beating of this signal?

I am trying to simulate the impact of a sinusoidal force on a Beam, yet I registred this beating signal (Displacement by time). The freaquency of excitation was the same as the first natural...

19 February 2021 5,872 3 View

How to apply a voltage sinusoidal/harmonic load in ANSYS APDL?

Hello all, I want to simulate a Dielectric Elastomer Actuator DAE (an electrostatic-Structural analysis). I want to apply various voltages and frequencies into the DEA in the form of sine wave....

13 February 2021 3,261 3 View

How to calculate time needed to evacuate a pressure from a tank using a pump?

Dear I have an air reservoir with 50 bar pressure , this reservoir is fed by 2 bar air pressure source, I would like to instal air pump ( 30 m3/h ) to evacuate the 2 bar fed pressure so I always...

06 February 2021 3,520 3 View

Observation instrument for classroom activity in consecutive interpreting?

Hello everybody My research involves an intervention where an instructor delivers a training course to students. My role as a researcher is to write down observations. Do you have any idea about...

03 February 2021 6,853 3 View

Inquiry regarding engineering journals for free publications for my dissertation (laser polishing of 3D printed parts?

my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?

01 February 2021 7,140 4 View

Is diversity in teaching methods for students important in communicating information?

Is diversity in teaching methods for students important in communicating information?

26 January 2021 3,387 7 View

Similar questions and discussions
Is there a way to use waveguide ports for circular antenna design in CST?

Hi, whenever i use circular array i get this error "Waveguide ports must be aligned with Cartesian coordinate planes for the transient solver" Does anyone use circular array with waveguide ports?...

09 February 2021 3,609 8 View

Where is the active point of VCSEL?

I am now working on the coupling between vertical-cavity surface-emission laser(VCSEL) and waveguide. However, the window design for laser emission is larger than the waist of Gaussian beam...

27 January 2021 8,318 1 View

How exactly modes are coupled into asymmetric directional coupler?

Currently I am reading one research paper regarding silicon based two and four mode division multiplexing for optical data transmission in 2 micrometer waveband. While reading I stuck at one...

21 January 2021 5,864 4 View

What is corrct way to define ports when simulating FSS and surface waves in CST?

I need to simulate a mushroom FSS and I'm struggling with the ports. What's the correct way to define them? Should I construct a proper SMA connectors, or is it enough to put a waveguide ports...

19 January 2021 6,590 4 View

How to make sure each cavity modes with same E-field distribution in COMSOL simulation?

In COMSOL Application Library, there is case about waveguide adapter. But there are some questions: 1) In boundary mode analysis, it just set to find only 1 mode and the S-parameter is...

12 January 2021 9,383 2 View

Is it possible to introduce a 2D axis-symmetric model in COMSOL Multiphysics to solve electromagnetic waves?

Hello dear researchers. I want to solve a cylindrical waveguide, lick an ordinary standard optical fiber. I am familiar enough with the 2D-axis-symmetric model, but as I knew from the equations...

11 January 2021 6,663 6 View

Can I bend a grounded coplanar waveguide (GCPW)?

The straight line shows great results but modelling just one bend in CST gives very high reflection. Could it be a tool error or are GCPWs supposed to be straight?

11 January 2021 1,606 4 View

Elastic constants -- transformation/basis change P21/a->P21/n?

Hi, I just calculated the stiffness tensor for a given material (a monoclinic molecular crystal) using molecular simulation. When trying to compare my results to published experimental results I...

05 January 2021 5,648 2 View

How to calculate width and length of the tapered microstrip line feed of a SIW leaky wave antenna?

With reference to substrate integrated waveguide -leaky wave antenna

26 December 2020 3,982 2 View

How to calculate tensile creep modulus of a liquid crystal polymer for a given load ?

Hi, I have the attached tensile creep modulus behavior for Vectra H140 (LCP material). The loads on the chart are 30 MPa, 40 MPa, whereas I am interested in the creep modulus for 15 MPa. Could...

15 December 2020 9,914 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close