Semi-active property of MR fluid is an advantage and how to realize it for different systems is important to find new applications.
Dear Prof. Selim Sivrioglu
There are many applications for the MR fluid, some of which are considered as damper, such as:
1- Car Suspension
2- Seat Suspension
3- Seismic Protection of Buildings
4- Cable Stayed Bridges
5- Washing Machine
6 -Prosthetic Knee
7- Artificial Muscles
And some other applications that you consider other than the damper, including
1- Hydraulic Valves
2- Brakes and Clutches
3- Polishing Devices
4- MR Fluid as a Robot Blood
5- MR Fluid as a Gun Recoil Protection
You can find an overview of all the applications mentioned in the published paper
https://inpressco.com/wp-content/uploads/2017/05/Paper932-37.pdf
Thank you very much for your valuable response Dr. Zakaria.
The simple answer is yes. MR dampers were used to control wind/rain induced vibration with the Franjo Tudjman Bridge (Cable stayed) in Dubrovnik, Croatia.
Thank you very much Dr. Ancich.
Hello dear Academicians, I am working on the forging of Mo alloys, but I wanted to consult you on an issue I could not solve. Mo is easily oxidized during forging and MoO3 is formed. Is it...
09 February 2021 1,989 3 View
Hello dear Academicians, I've been struggling on a specific subject for a while. Hence, I'd like to get some advice. I am working on Mo-0.5 Ti alloy production via powder metallurgy technic. I...
20 December 2020 3,805 2 View
Hello dear Researchers, I've been working on to produce Mo-Ti alloys via powder metallurgy method. Yet, I've come across a problem: I can not properly distribute Titanium in Molybdenum host. I'm...
10 August 2020 4,502 3 View
10 August 2020 5,909 4 View
I have prepared 15wt.% PDMS and poured it on a glass petri dish, then let it dry for 72 hr at room temp. after I tried to peel it and it doesn't work, so I am crosslinked in an oven for 3 hr , but...
26 July 2020 9,892 2 View
For membrane preparation PVDF will be used , and I was wondering which solvent is the best for dissolving it, non-Toxic solvent , useful in dissolving other polymers such as PES, PDMS, Peba
05 July 2020 1,655 5 View
I want to create a Deep Learning Model for 3D Construction of Breast Cancer in CT Images. However, I cannot find an appropriate data-set or research paper. The data-set should be multiple CT scans...
04 March 2020 3,614 3 View
High Fidelity Mathematical Modeling of Reaction Wheel Performance (AAS 98-063) Bialke, B. /Guidance and Control 1998. (Advances in the Astronautical Sciences )
26 January 2020 813 2 View
There are too many information about this topic presented below: 2.4 mm Metal (Steel) Beads are recommended for hard tissues, skin, muscle, bone, hair 2.8 mm Ceramic Beads are recommended for...
15 November 2019 3,799 3 View
Does anyone have any clue or idea about drawing block diagram of this bond graph ? This problem is very important for me so any little help is appreciated. Thanks.
10 June 2019 4,427 1 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...
02 March 2021 1,999 5 View
during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...
01 March 2021 7,476 4 View
I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...
01 March 2021 6,985 3 View
I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...
01 March 2021 8,668 3 View
How can one improve mesh skewness, orthogonality, aspect ratio?
28 February 2021 7,730 3 View
Hello, I am looking for some expertise on culturing MCF7s. I purchased them from ATCC and I have been following all media and culture conditions. Media is EMEM with 10% FBS and 10ug/mL of...
27 February 2021 3,904 2 View
I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...
25 February 2021 2,615 3 View
Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...
25 February 2021 9,602 4 View
I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?
25 February 2021 7,187 3 View