How the year 2021 can be made good for global community?

Many steps can be taken to make the year 2021 good for humanity. For instance, if powerful and rich countries decide and spend some part of their resources for the improvement and betterment of...

30 December 2020 830 4 View

What was the most worst thing and what was the most beneficial thing that happened for global community in 2020?

Many bad and good things happened for global community in 2020. However, the present question is about one top most worst thing and one top most good thing that happened in the world in 2020 and...

30 December 2020 6,262 3 View

What can happen in the world if large scale melting of continental and alpine glaciers occurs?

Several environmental experts have warned about the global warming and its effects on different ecosystems. It may also cause large scale melting of continental and alpine glaciers. If this...

23 December 2020 4,630 3 View

Is there any relationship/correaltion between 1) elastic modulus and adhesion or 2) elastic modulus and density of solid material or polymers?

21 December 2020 1,853 3 View

I am performing enzyme inhibition assay and the substrate is fluorogenic & fluorescence was measured. Now I want to calculate Vo and Vi. How can I ??

These are the per minute fluorescence observed. Please guide me how can I determine Vi, Vo and IC50 ? By slope determination or any other method? Control: 28.11 40.30 40.78 37.61...

11 December 2020 1,037 4 View

Which countries have comparatively more secure future, agricultural or industrial?

Agriculture provides for almost all the basic needs essential for survival and industries provide mostly the luxury commodities required for comfortable life. However, some countries are heavily...

07 December 2020 2,153 15 View

How many fish kinds are found in the world and how much of them are edible as human food?

About 71% of the earth's surface is covered by the water bodies which contain huge amount of creatures. Humans are commonly concerned with fish because it is consumed almost in every part of the...

06 December 2020 8,146 4 View

Is electromagnetic radiation seriously harming immune system of human body?

Presently we are living in 'electronics age'. Use of electronics has dominated every sphere of life in almost all parts of the world. All electronic appliances release electromagnetic radiation...

08 November 2020 1,558 2 View

How can I apply Cyclic loading in ANSYS Mechanical APDL as a second Load step after a Static 1st Load step?

I am simulating a masonry wall under in-plane cyclic loading. Before the cyclic load is applied, it must be loaded with gravity direction surcharge load (or pre-compression). However, whenever I...

14 October 2020 3,253 1 View

I am operating 2.5 MGD combined effluent treatment plant but the pH is increasing in the aeration tank and reaching 9.2 which is affecting microbial?

Any one can guide me that how can I increase MLSS concentration in aeration tank of Activated sludge process. The pH of influent coming from primary clarifier was 7.1 and after taking water in...

30 September 2020 8,846 7 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

How do I choose contrasts in SPM8?

I am learning how to use SPM for PET and PET-MR analysis, but I haven't found any great resources that explain how contrasts work. I have a series of PET images where our hypothesis argues that...

24 February 2021 1,534 2 View

Suggestions for occupational stress surveys?

I am currently writing a masters thesis on reasons for occupational stress in the early childhood classroom, and want to include a short survey assessing participants work-related stress levels. I...

24 February 2021 8,678 2 View

Fractional impervious surface (FIS) map ?

Need Help Does anyone Know how to make a Fractional impervious surface (FIS) map from NDVI map, in ArcGIS environment? Thanks in advance

24 February 2021 8,455 2 View