How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

Can i quantify protein concentration in sds page?

I have to quantify a mixture of proteins. But I can not quantify its concentration by any protein detection methods as the values fluctuate. Can i quantify the protein concentration by sds page?

22 February 2021 215 2 View

Can fractal dimension of thin film surfaces affects the electrons energy states?

As fractal dimension of a thin film surface implies the irregularity in the surface. Is it possible that the energy states of the electrons are also affected by the fractal dimension?

19 February 2021 5,509 3 View

Can we use image data in MATLAB Neuro Fuzzy Designer ?

I have remotely sensed data (image) that I want to use in the Neuro-Fuzzy Designer apps of MATLAB. Is it possible to use an image file in the Neuro-Fuzzy Designer app or only numeric data is...

17 February 2021 1,205 5 View

Is it possible to determine % K2O of organic manures by STPB method ?

To determine % K2O of organic manures, flame photometric technique is used whereas in inrganic fertiliser for K2O determination STPB method is used. I am trying to find out any method of...

24 January 2021 4,714 3 View

How to tackle "CONSTRAINT CONTROLS" error while using tie between CFRP and frame segment in abaqus?

Hello, I had been trying to model a portal frame wrapped with CFRP in ABAQUS. To tie the CFRP laminates with frame I need to use slave/master surface interaction. But whenever I try to model the...

19 January 2021 2,906 3 View

How to remove colour from DNA pellet during DNA extraction?

I am working with Amaranth accessions which are green to red in color and contain high phenolic compounds. Using the CTAB method with the slight modification I am trying to get high-quality DNA so...

18 January 2021 3,578 1 View

Why the mixture of NaOH solution (10-12M) and Na2SIO3 solution is getting solidify after mixing?

These days I am noticing that the mixture of NaOH (NH) (10-12M) and N2SiO3 (NS) solution gets solidify after 24 hours. The ratio of mixture of NS to NH is 2. To mention, the same solutions that we...

18 January 2021 7,911 2 View

Which model is most suitable for urban simulation?

Respected sir/mam, I want to simulate the urban expansion using different time series LULC based on satellite image. please suggest me most suitable model for urban simulation. Thanks and regards.

17 January 2021 9,134 11 View

Is there any packages or code of MATLAB for solving a system of stochastic delay differential equation?

Hello, Can you help me regarding MATLAB solver for a system of stochastic delay differential equations? To be specific the system is delay differential equation where parametric stochasticity is...

15 January 2021 6,950 7 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View