Does anyone know where I could find DICOM files for CT artifacts ?

More Bazhdar Noureddin Mohammed's questions See All

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

Can anyone suggest a topic for the Impact of AI and ML in the financial institutions?

I am currently doing my Master Thesis in FinTech and I am thinking of doing my project on the impact of AI and ML on the financial industry but as the impact of these technologies on the industry...

21 February 2021 7,128 3 View

Where I can find materials to learn Fuzzy VIKOR methodology?

Please suggest ways to learn Fuzzy VIKOR methodology in a best possible way. And is there any toolkit available for the same? Thank you in advance.

20 February 2021 8,271 3 View

What cause the beating of this signal?

I am trying to simulate the impact of a sinusoidal force on a Beam, yet I registred this beating signal (Displacement by time). The freaquency of excitation was the same as the first natural...

19 February 2021 5,872 3 View

How to apply a voltage sinusoidal/harmonic load in ANSYS APDL?

Hello all, I want to simulate a Dielectric Elastomer Actuator DAE (an electrostatic-Structural analysis). I want to apply various voltages and frequencies into the DEA in the form of sine wave....

13 February 2021 3,261 3 View

How to calculate time needed to evacuate a pressure from a tank using a pump?

Dear I have an air reservoir with 50 bar pressure , this reservoir is fed by 2 bar air pressure source, I would like to instal air pump ( 30 m3/h ) to evacuate the 2 bar fed pressure so I always...

06 February 2021 3,520 3 View

Observation instrument for classroom activity in consecutive interpreting?

Hello everybody My research involves an intervention where an instructor delivers a training course to students. My role as a researcher is to write down observations. Do you have any idea about...

03 February 2021 6,853 3 View

Inquiry regarding engineering journals for free publications for my dissertation (laser polishing of 3D printed parts?

my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?

01 February 2021 7,140 4 View

Is diversity in teaching methods for students important in communicating information?

26 January 2021 3,387 7 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View