Does anyone know of materials used for glob topping wire bonds other than epoxy based glob tops?

More Peter Knapen's questions See All

I have a time series data of some biochemical studies ( DNA and Chromosomal damage) which I intend to use to further predict into future ?

I have a time series data of some biochemical studies ( DNA and Chromosomal damage) which I intend to use to further predict into future without necessarily conducting the assay for an extended...

23 February 2021 7,842 1 View

No mRNA increase in PCR after successful transfection in ARPE-19 cells ?

Hello, i am a bit curious about my results. I transfected the human cell Line ARPE-19 with a Plasmid containing a GFP tagged p53 (p53-GFP, Plasmid #11770). After 24h i checked under the...

18 February 2021 3,811 7 View

Do there exist stand-alone permanently in-ground soil-moisture sensors with an installed GSM module, for outdoor use?

Am searching for a stand-alone permanently in-ground soil-moisture sensor with an installed GSM module, for outdoor use. The idea is for the sensor to send a moisture reading via a cellphone text...

04 February 2021 2,047 4 View

What is the easiest way to remove the water from organic solvents?

Hello everyone! I have one question. I have couple of solvents and all of them were pure when they were bought but after some months or years of storage after opening I am not 100% sure about...

03 February 2021 2,154 8 View

Virus neutralization assay in BSL2 lab?

Hi I want to set up a virus neutralisation assay such as PRNT or FRNT at my lab (BSL2), but im uncertain of the bio safety requirements that has to be fulfilled in order to work with...

01 February 2021 5,626 3 View

Using LINK11 to Apply force in ANSYS APDL?

I'm trying to use LINK11 to apply a force as if it was a cable pulling a structure twowards a point in ANSYS APDL. When I solve the model, the deformation of the overall structure is far too...

30 January 2021 7,919 1 View

Cytoflex Flowcytometer, clotting issues and cleaning procedures?

We have been having clotting issues with our Cytoflex S from Beckman Coulter. Back in December 2020, we had to have the tubing system and sample needles replaced, but we are beginning to observe...

28 January 2021 6,897 2 View

Difficulties purifying Outer Membrane Vesicles using a Sucrose Density Gradient: Unable to detect any protein after this process?

I'm currently trying to purify Outer Membrane Vesicles (OMVs) following their extraction from the bacteria I'm working with. After the initial extraction the concentration of protein seems good...

27 January 2021 6,852 3 View

What excamples do you know wasting unused contents of "empty" packaged products?

Most of us use tooth paste more times a day. The empty tube we throw away. I wondered how empty the tube really is. This does not sound being Research? I began to collect empty tubes...

19 January 2021 808 3 View

What is the largest disadvantage in using of face masks at present? What would you like to be improved?

We all use face masks many hours a day. I wonder what are your items you like to be improved. We have the opportunity to write an application for support to a sponsor. Your answers will help us a...

18 January 2021 1,311 4 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

For gelatin coating for culturing HUVEC.Should the gelatin be made in sterile water or PBS? Do I need to autoclave the gelatin soln after making it ?

I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?

28 February 2021 274 2 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View

Artem Grebenko

Dear Peter,

We havr tried using various waxes, depositing them thermally. Also you can try using crosslinked pdms or plasma deposited amorphous "polymers" from IPA or acetone in gas phase. The cast variant is a bit complex, but realizes good thermally conductivity. However it is not a very good insulator, and big thicknesses require really long deposition times

Peter Knapen

Hi Artem,

Thanks for your input. Could hyou eleborate a bit more on the cast variant and how this process is being done?