Hi,
I was wondering if anyone knew of any XRD data on nanocrystalline copper steel FC0205 powder?
I tried indexing the peaks and I'm getting FCC in one case and simple cubic using a different method.
Thanks in advance for the feedback!
Dear Sir,
I hope that this links could helped you in your project.
Best regards,
Dragan Vuksanović
http://prism.mit.edu/xray/Basics%20of%20X-Ray%20Powder%20Diffraction.pdf
http://203.115.126.36/ebooks/ASM%20Handbooks/07%20-%20Powder%20Metal%20Technologies%20and%20Applications.pdf
Thank you so much Dragan! You are awesome.
You are welcome.
Dragan
Are there any papers with data supporting the impact of "after school" & "summer program" attendance and the post effects they have on K-12 student competency in math, science, & reading?...
01 February 2020 9,861 2 View
It would be nice to have a root cause failure analysis guidebook to validate some of the common failures I am witnessing in pipes and other materials on an industrial plant near me. I remember an...
31 December 2017 7,069 4 View
Hi, I am trying to obtain the gauge factor equation (G = dR/R*epsilon) from the resistance, electrical conductivity, length, and cross sectional area, A (width and thickness) of material. I have...
07 August 2017 2,271 3 View
I generated several stress-strain curves and I am finding a slight decrease in the modulus and the tensile strength of the CNT/epoxy systems. Are there any explanations as to why this may be...
08 September 2016 6,473 4 View
Hi All. Are there any analytical equations that can help me to understand aligned vs random CNTs placed in a polymer nanocomposite? I want to gain some type of conceptual understanding of how the...
05 June 2016 991 2 View
Hi All, I am curious to know if I can perform a sensitivity analysis of CNT/Epoxy films using ANSYS? I know it's possible to figure out the properties of the epoxy, but I am not sure on how to...
01 February 2016 316 3 View
Hi all, I know this is a crazy question to ask... but my brain is spinning for some reason. I am going to disperse nanotubes into a polymer matrix post solution mixing. However, I am worried that...
31 December 2015 2,072 5 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View