Does anyone know any reference regarding modelling of check valve?

Kamil Jerzy Chodzyński @Kamil_Chodzynski

04 April 2014 1 987 Report

I am searching some data about modelling of a check valve. I have this type of check valve:

http://www.amazonsupply.com/thomas-kynar-viton-chemical-resistant/dp/B006T5AP78

It is a simple rubber-disc check valve. I need to model dynamic behaviour of this valve. Do you know any books or whatever where I can start?

Thanks in advance.

Kamil Jerzy Chodzyński

I found something interesting if anybody will need:

http://gasturbinespower.asmedigitalcollection.asme.org/article.aspx?articleid=1429629

Badges
Science topic

More Kamil Jerzy Chodzyński's questions See All

How to calculate disipation of the energy between two parallel plates with small gap?

Hi all, Does somebody has any experience with flows between two parallel plate with small gap? I am trying to understand the dissipation of the energy due to small gap between (0.2mm) the plates....

04 May 2018 3,269 2 View

How are the limitation of the Anton Paar MCR 302 rheometer?

Hi all, I have opportunity to work with Anton Paar MCR 302 rheometer with double gap system. I would like to measure low viscosity fluid between 1mPa.s to 1000mPa.s in the range of the shear...

01 February 2018 7,895 1 View

How to take a picture/movie of the reflective object without reflection?

Hello, I would like take a picture/movie of the reflective object (see picture) but I have reflection of the light. I use a shadowless tent, plus 3 lamps, polarized filter...but still I have...

31 December 2013 8,427 9 View

How to calculate/indicate revers wall shear stress in Comsol?

I calculated the flow in arteries and I would like to show that for some time steps the wall shear stress has the opposite direction, for example in the curves, branches, etc. For the straight...

03 April 2013 8,224 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View