Does anyone have the Matlab code for the State Space analysis of Doubly Fed Induction Generator?

More Tej Enosh's questions See All

How UAV or drone can be beneficial to better estimate crop yield?

As we know, crop yield estimation has been done traditionally with farmer's expert knowledge, deductive sampling in representative areas, and remote sensing with satellite imagery. Farmer's Expert...

01 March 2021 3,468 3 View

How to combine the confusion matrix of two phase classification?

I have performed a two-phase binary classification to solve the 3 class problem: Normal-86, Disease A-86, and Disease B-86 (figure attached) Phase I: Normal vs. Abnormal (Disease A + Disease...

06 July 2020 5,537 1 View

How to generate heterozygous knockouts using CRISPR Cas9 in iPSCs?

Hi all. I'm trying to create a heterozygous deletion (55bp) mutation in iPSCs to model malignant tranformation. I'm using two sgRNAs in a plasmid based system (puromycin selection). I obtained ~20...

18 May 2020 5,389 1 View

Co-Relation between Inverter temperature, Ambient Temerature and Inverter Efficiency?

Is there any specific book/research paper where i can find a validated model of relation between Inverter temperature, Ambient Temerature and Inverter Efficiency? Reduction in Inverter's...

22 February 2020 7,154 5 View

How to save an image with some plots over it using Matlab?

I have plotted some rectangles over a image now I want to save the image or store it on some variables, so as it can be used for further processing. Please suggest me any method to do that.

18 October 2018 8,176 1 View

What is the reason for seedlings tip drying in the tissue culture conditions?

Dear Sir/Madam, I am growing citrus seedlings of different crosses in MS culture medium both liquid and solid. Growing conditions are 27 degree Celsius and light period 8h light and 16h dark....

22 August 2017 6,249 6 View

How make a Systems biology networks given that I know the state of regulation of proteins?

I have the list of proteins which are either inhibited or induced by action of certain small molecule. I would like to know the downstream effects of this action so that I can hypothesise a mode...

20 June 2017 1,185 2 View

How to separate ATP ADP and AMP form a sample?

The sample was made by mixing the powders of the 3 components and adding a solvent. I cannot find 3 peaks for the 3 components but I get a cumulative peak area of the 3. I tried 2-3 methods till...

07 April 2015 6,568 2 View

Are there softwares to manage clinical data?

I would like to have a software to manage large amounts of clinical data.

02 May 2013 5,553 3 View

Primary antibody for DSRed is not working for western blot. Is any one having the same problem?

I have also done immunoprecipitation of both cell lysate and medium but I have not had in western blot. Commasie staining is also not showing the band of DSRed.

07 March 2013 4,974 1 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

Sivaraman Pandarinathan

I will give the guidance but there is no matlab code from me.