frequency > 1khz
Pisupati Sadasiva Subramanyam · Vignana Bharathi Institute of Technology
The main factors affecting the high frequency performance are the eddy current
Follow a mazumdar sir paper and Vikram rathore ppaper
Contemporary CAD software can successfully handle such a task. But there are some problems may occur due to you are dealing with high frequency. In this case you may need to develop your own software.
Please have a look at:
http://wwwlea.uni-paderborn.de/fileadmin/Elektrotechnik/AG-LEA/forschung/veroeffentlichungen/1995/95APEC-Becker-Grotstollen-ComputerAidedDesign.pdf
http://www.umc.edu.dz/vf/images/ieee-magnetique/jpdfs/ieee/mag/tmag/2010046/08aug/3249abed.pdf
losses,leakage flux and the effects due to the transformer elements, where the
transformer is part of the resonant converter.
No accurate model of the transformer taking into account the high frequency range
has been performed yet
1. However the Following Ph.D Thesis BY ADILH.MUHAMMED,
MPhil may be of Good Help.
HIGH FREQUENCY TRANSFORMER, DESIGN AND MODELLING USING FINITE
ELEMENT TECHNIQUE
A THESIS SUBMITTED tTO NEWCASTLE UNIVERSITY
Link:
https://theses.ncl.ac.uk/dspace/bitstream/10443/747/1/Muhammed00.pdf
2. Optimum Design of a High-Power, High-Frequency Transformer
R.Petkov
IEEE TRANSACTIONS ON POWER ELECTRONICS,
VOL. 11, NO.1, JANUARY 1996
http://bbs.dianyuan.com/bbs/u/66/1560141214276400.pdf
For Modeling Packages You may also Refer to the Thesis by Valentin Bolborici for Master of Applied Science, 1999 to University of Toronto
Design of Low Profile Transfomers for High Frequency Operation
https://tspace.library.utoronto.ca/bitstream/1807/14979/1/MQ45982.pdf
P.S.
thanks
Read 5 answers by scientists with 15 recommendations from their colleagues to the question asked by Hossein Harimi on Dec 13, 2014
11 December 2014 1,874 6 View
exp: multi level converter ac to dc or CHB(CONVERTER H-BRIDGE)
10 November 2014 9,682 4 View
Read 20 answers by scientists with 145 recommendations from their colleagues to the question asked by Hossein Harimi on Nov 8, 2014
10 November 2014 3,961 19 View
H-bridge converter AC - DC input voltage:10 k volt output voltage:1200 volt efficiency: upper 90%
10 November 2014 3,418 10 View
How to Stability Analysis of Nonlinear Systems with Simulink/Matlab ?
10 November 2014 3,688 8 View
What Are the Option Method research?
09 October 2014 9,883 2 View
What is the best(accurate) software for a power electronic simulation? Recommend: matlab/simulink/pspice/...
09 October 2014 5,080 5 View
There is clear evidence of changes in the composition of the greenhouse gases in the lower atmosphere, with CO2 in particular steadily increasing to its present level of about 400 ppm.
09 October 2014 7,080 9 View
How can I design SST with Simulink/Matlab?
09 October 2014 7,829 1 View
Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.
09 October 2014 6,191 0 View
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks
06 August 2024 949 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View