Does any one have good litrature on epoxy curing and aging under hot/wet conditions?

Anagi M Balachandra @Anagi_Balachandra

03 March 2018 0 9K Report

I am looking for molecular changes (polymer physics) rather than chemistry/chemical change

Badges
Science topic

Similar topics
Chemistry

More Anagi M Balachandra's questions See All

Can XRD provide amorphous content in a material?

I need percentage of amorphous content through XRD.

01 February 2019 3,156 15 View

What is Reitvled Analysis in XRD?

What softwares are capbale of doing it?

01 February 2019 1,267 3 View

How to do quantitative analysis with XRD?

What softwares are capable of doing it? Do I have to add internal standards? Is there a procedure of doing it?

01 February 2019 7,132 3 View

How surface roughness and chemical functionalities affect on epoxy curing?

I am interested to learn about work done on surface roughness, wettability, chemical functionalities affect on epoxy polymerization and curing. I am specifically interested on epoxy coatings on...

10 November 2017 3,532 0 View

How to deal with full text requests on publishd papers that are subjected to copyright

I am very sensitive to copyright laws and trying to comply with it. Does anyone know how to deal with the full text requests on papers from publishers that are subjected to copyright? Example I...

01 January 1970 4,933 3 View

I would like to get any input on available techniques to measure the quality of epoxy/metal or epoxy/alumina interface during cure and aging?

I am specially interested in measuring local defects at the interface to monitor premature failure.

01 January 1970 7,297 6 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Inquiry on Maximum Nucleic Acid Volume for 2.5 mL Liposome Solution?

I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...

30 July 2024 6,420 1 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

EDC carbodiimide and NHS easter 's half life among different pH?

It has been long known that EDC carbodiimide and NHS easter's half life agains hydrolysis are highly related to pH. However, very surprisingly, not yet found a paper giving a table/chart of their...

25 July 2024 8,738 0 View

Is the zero-zero component of the metric tensor equal to 1 for accelerating reference frames?

Consider the case of negligible gravity but there is an accelerating reference frame. Its origin traces out a trajectory, or world line, seen in some inertial reference frame. The Lorentz metric...

24 July 2024 1,608 15 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

How to eliminate the carry-over effect in GC-MS/MS system?

Hi, I am a PhD student working at Jagiellonian University, Faculty of Chemistry. My work is related to the development of new analytical methods for the quantification of short-chain fatty acids...

22 July 2024 5,492 6 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View