The procedure compute?

02 March 2021 5,204 3 View

One-sided testing of MLM in R?

Dear colleagues, Does anyone know how to conduct a one-sided testing of regression weights (MLM) in R? The actual model is fm1rs

23 January 2021 3,970 3 View

[Measurement invariance] - Do you test it on the full SEM model, on each construct separately, or both?

Hi everyone, I would like to know whether both cultural groups interpreted my questionnaire in a similar way. To do so, I conducted a measurement invariance analysis on the whole model of latent...

14 January 2021 1,845 3 View

Is it possible to do a closed loop control of a sine wave?

An analogue voltage sine wave signal is send from a PLC to a Piezo actuator. This actuator converts the voltage to force. A load cell checks what the applied force is and sends a mA-signal...

27 December 2020 7,037 3 View

[SEM] Why RStudio and AMOS report different p-values (but same estimates)?

Hi everyone, I have conducted a SEM analysis in AMOS then replicated it in RStudio. While I obtained identical estimates and model fit statistics, the p-values differ between software programs...

25 December 2020 3,669 4 View

What should my boundary conditions be in abaqus and how do I apply a sine load?

I want to model a T bone specimen that is subjected to a sine load. The specimen is clamped in as showed on the figure. I was wondering what I should chose as boundary conditions and how I can...

08 November 2020 9,766 4 View

Does anyone know instruments to measure "mental health literacy" in teachers?

Hi there, I am looking for questionnaires measuring mental health literacy in teachers and educators. does anyone know any studies in this area?

16 September 2020 1,682 4 View

Is there any possibility to get the estimated values (listed for every participant) of a specific latent variable in R or Mplus?

Is there any possibility to get the estimated values (listed for every participant) of a specific latent variable in R or Mplus?

17 June 2020 3,819 3 View

Literature for multilevel MCMC models?

Hey there, I am looking for literature or tutorial videos, which are concerned with the question of how multilevel markov chain monte carlo models are conducted in R or Mplus. Can someone help...

20 April 2020 7,801 1 View

How to generate a ROC-Curve for multilevel regression models?

Dear colleagues, Does anyone know, how to build a ROC-Curve and a AUC-Value concerning multilevel logistic regression models using R or Mplus. I would be very grateful for any articles,...

26 February 2020 8,930 3 View

How does one access the Cranet survey data on HRM practices?

Hello, The Cranet website does not provide any lead to the data obtained from their multinational survey on HRM practices. Any help on accessing the data would be most appreciated. Thank...

01 March 2021 9,536 3 View

Is there any research regarding how training and development is going to change in the era of Fourth Industrial Revolution?

As the organizations getting prepared for the fourth industrial revolution, to enhance the skills of their workforce what type of changes are necessary and going to occur in the training and...

01 March 2021 3,199 3 View

How long does it take to get a modeller(for homology modelling) license?

I submitted my e-mail address on modeller website to get a license. The problem is that, the site cannot process my school e-mail (ewhain.net). I submitted my Lab website and school name so that...

25 February 2021 9,054 3 View

Assistance in finalizing and publishing an article on human resource management in forestry?

Dear colleagues! We have prepared an article on the current status of human resources potential of municipal state forest management institutions of Kazakhstan. Since this is my first experience...

16 February 2021 8,611 3 View

In what ways 'Human Resources' of institutes are affected during COVID-19 pandemic?

It is found that during the COVID-19 pandemic the human resources of institutes are affected in many ways. What are those?

16 February 2021 3,675 11 View

PV system design. 3d modelling and Analysis?

I have been looking for a good cost-effective tool for 3D modelling a glass-glass solar module system. I was initially considering Skelion as a tool but it does not look very promising, a bit...

13 February 2021 8,126 1 View

How to compare different models with different inputs and data length?

I want to run 5 different models to estimate stream flow. In order to optimize the characteristics of these models I use Taguchi method. So I have to run different models according to the Taguchi...

11 February 2021 7,986 6 View

Is it possible to get compass potential paramters from MATERIALS STUDIO 6.0?

Hi all, I wonder whether we can get potential parameters from material studio. I have a licensed version available. If I use polymers and cnt in materials studio to perform MD simulations,...

03 February 2021 7,673 3 View

What could be the reason for XRD pattern starting from very high counts/intensity at 3 degree 2 theta?

I am working on XRD analysis of the clay minerals from the sea sediments. My XRD pattern shows very high counts at the start of the XRD pattern (3 degree 2 theta) which is very unusual. The counts...

31 January 2021 4,493 9 View

Is it possible to prepare clay minerals by mixing pure oxides of required elements? What would be theoretical difficulties with it?

Practically this is not at all necessary. But theoretically, would hydrous/hydrothermal synthesis be enough (like mix 1 mole alumina gel and 4 mole silica gel and gently heat) or would it require...

26 January 2021 6,403 3 View