22 March 2024 1 6K Report

I know of a place in Tamil Nadu where for one sample cost is 5000. I am looking for a cheaper alternative.

More Muralishwara Kakunje's questions See All
What is the harmless way of cutting epoxy filled nanocomposite ?

I want to cut epoxy filled nanocomposite for FE-SEM analysis. What is the best way to cut it without resulting in any cracks or change in position or alignment of the particle reinforcement ? Also...

28 January 2021 7,084 5 View

How to prepare the sample of polymer nanocomposite for SEM analysis ?

Does Epoxy clay nanocomposite sample require surface preparation. I am going for Gold sputtering to make the surface conductive. I guess there is no need to clean or polish the surface beneath the...

04 January 2021 1,943 8 View

How to measure diffusion coefficient of filled polymers other than standard immersion tests that consume lot of time and resource ?

Diffusion coefficient of filled polymers are experimentally determined by standard water immersion test (ASTM D570). This will enable us to determine percentage increase in weight with respect to...

15 November 2020 9,790 4 View

What is the difference between permeability and diffusivity ?

In polymer clay nanocomposites, researchers have studied water absorption by measuring the weight of specimen periodically when immersed in water. Diffusion coefficients are measured. How is...

29 October 2020 1,422 10 View

What could be the maximum amplitude in a ultrasonication process ?

If I can limit the temperature build up during the ultrasonication process, can I increase the amplitude from 30 to 100 % and observe the changes in the prepared nanocomposite. Some people are of...

12 March 2020 2,503 3 View

How to produce epoxy and epoxy nanocomposite free or free standing films ?

In order to analyze epoxy neat and nanocomposite coatings in SEM, AFM, etc. I need free or free-standing films. How do I produce them? Basically, if I coat the epoxy nanocomposite on a substrate,...

17 December 2019 3,367 5 View

Where can I buy air bubble release agent for epoxy from (only ones in India reply) ?

I found air bubbles in the cured epoxy coatings. I do not have a vacuum oven, vacuum pump, thinky mixer, etc. in order to remove the entrapped air. I came to know that there are bubble release...

11 December 2019 185 3 View

How to remove solvent without the aid of any equipment ?

After preparing epoxy clay nanocomposite using the solution intercalation method, how can the solvent be removed? I do not have a vacuum oven, vacuum pump, degassing equipment, etc. Are there any...

29 November 2019 4,076 2 View

Is afra heavy duty silicone spray or release agent compatible with epoxy ?

Application: to peel out epoxy coating from mild steel or glass substrate Basically I am going to apply epoxy coating on a substrate. But since I want to peel out the coating for further AFM/SEM...

20 November 2019 5,057 1 View

What is the glass transition temperature of LY 556 epoxy cured with HY 951 cured in room temperature for one week ?

I have used LY 556 and HY 951 in a 10:1 ratio and cured at room temperature for one week. Has anyone determined the glass transition temperature for this combination when cured at room temperature?

11 October 2019 3,393 3 View

Similar questions and discussions
what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

Ester cleavage conditions?

Hi all, I need to cleave the ester in Ethyl 2-amino-1H-imidazole-5-carboxylate to make the carboxylic acid and retrieve the product from solution to use in downstream applications of linking to...

01 March 2021 8,766 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close