What are some Q1 journals to publish research work on natural fibers ?

Muralishwara Kakunje @Muralishwara-Kakunje

23 December 2023 1 5K Report

Journal of natural fibers seems to have come down to Q2.

Muralishwara Kakunje The following journals cover materials science and engineering, including natural fibers, with a broad scope, including Advanced Materials, Science Advances, Nano Letters, ACS Applied Materials, Polymer Composites, Green Chemistry, Biomacromolecules, and Materials Today.

Badges
Science topic

More Muralishwara Kakunje's questions See All

What is the harmless way of cutting epoxy filled nanocomposite ?

I want to cut epoxy filled nanocomposite for FE-SEM analysis. What is the best way to cut it without resulting in any cracks or change in position or alignment of the particle reinforcement ? Also...

28 January 2021 7,084 5 View

How to prepare the sample of polymer nanocomposite for SEM analysis ?

Does Epoxy clay nanocomposite sample require surface preparation. I am going for Gold sputtering to make the surface conductive. I guess there is no need to clean or polish the surface beneath the...

04 January 2021 1,943 8 View

How to measure diffusion coefficient of filled polymers other than standard immersion tests that consume lot of time and resource ?

Diffusion coefficient of filled polymers are experimentally determined by standard water immersion test (ASTM D570). This will enable us to determine percentage increase in weight with respect to...

15 November 2020 9,790 4 View

What is the difference between permeability and diffusivity ?

In polymer clay nanocomposites, researchers have studied water absorption by measuring the weight of specimen periodically when immersed in water. Diffusion coefficients are measured. How is...

29 October 2020 1,422 10 View

What could be the maximum amplitude in a ultrasonication process ?

If I can limit the temperature build up during the ultrasonication process, can I increase the amplitude from 30 to 100 % and observe the changes in the prepared nanocomposite. Some people are of...

12 March 2020 2,503 3 View

How to produce epoxy and epoxy nanocomposite free or free standing films ?

In order to analyze epoxy neat and nanocomposite coatings in SEM, AFM, etc. I need free or free-standing films. How do I produce them? Basically, if I coat the epoxy nanocomposite on a substrate,...

17 December 2019 3,367 5 View

Where can I buy air bubble release agent for epoxy from (only ones in India reply) ?

I found air bubbles in the cured epoxy coatings. I do not have a vacuum oven, vacuum pump, thinky mixer, etc. in order to remove the entrapped air. I came to know that there are bubble release...

11 December 2019 185 3 View

How to remove solvent without the aid of any equipment ?

After preparing epoxy clay nanocomposite using the solution intercalation method, how can the solvent be removed? I do not have a vacuum oven, vacuum pump, degassing equipment, etc. Are there any...

29 November 2019 4,076 2 View

Is afra heavy duty silicone spray or release agent compatible with epoxy ?

Application: to peel out epoxy coating from mild steel or glass substrate Basically I am going to apply epoxy coating on a substrate. But since I want to peel out the coating for further AFM/SEM...

20 November 2019 5,057 1 View

What is the glass transition temperature of LY 556 epoxy cured with HY 951 cured in room temperature for one week ?

I have used LY 556 and HY 951 in a 10:1 ratio and cured at room temperature for one week. Has anyone determined the glass transition temperature for this combination when cured at room temperature?

11 October 2019 3,393 3 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Distribution of particles in metal matrix?

How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...

28 February 2021 7,397 8 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View