Do I have a problem with creating a 3D soil model using OpenSees?

30 May 2025 0 6K Report

Dears,

I am creating a 3D soil model using OpenSees. I received errors and warnings, although I believe all steps are correct. I am attaching all my TCL files. Can anyone help me to figure out the problem?

Badges
Science topic

Similar topics
Mathematical Sciences
Graphs

More Khaled Sobhy Emam's questions See All

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

How much Yeast should we add to fermentation media?

I have prepared a liquid broth containing Yeast (S. Cerevisiae) that i need to add from it to fermentation media of lignocellulosic hydrolysate. I need to know based on what parameters do we add...

06 August 2024 662 1 View

How good can CI users localize sound?

It is probably pretty variable between CI users, any ideas?

24 June 2024 6,879 1 View

How can I increase the acidity in paper samples? or How can I do the Acid aging in paper samples ( restoration department) ?

The Acid aging in paper samples

10 June 2024 6,456 2 View

Is the Journal of Pedagogical Research is a trusted journal to publish in? I check in scopus and it is there but I have concerns if it is predator?

Is the Journal of Pedagogical Research a trusted journal to publish in? I checked in scopus website and scimago and I find it is there with scopus Q2 rank; but I have concerns if it is predator?...

08 June 2024 7,678 2 View

Chapter Invitation: Genome Editing for Sustainable Agriculture Book Series Vol 1 Plant Genome Editing Development and Technologies (Springer)?

Forthcoming Springer book: Genome Editing for Sustainable Agriculture Book Series Vol 1 Plant Genome Editing Development and Technologies (Springer) edited by Khaled F. M. Salem, Jameel M....

08 May 2024 5,043 0 View

Can't we notice something about the pattern of distribution of prime numbers?

There is a usual pattern for the distribution of prime numbers, such as $2n+n$, but within the pattern of prime numbers there is some implicit distribution.

08 May 2024 478 0 View

Trypsine powder preparation reference?

Hello Please I need urgently a book as reference for trypsine powder dilution to use in tissue culture. With respects

28 April 2024 6,136 0 View

Pcr product different than fragment designated primer?

I designed a primer for gene sequence(1480 bp) and when carried PCR, the product was 150 bp, what is the problem? and how to obtain the correct fragment?

19 March 2024 170 3 View

JPDS [ XRD] reference?

How to get JPDS [ XRD] reference to compare XRD patterns obtained for activated carbon prepared from agriculture waste ?

24 February 2024 2,816 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How do soil microflora interact with plant roots and influence plant nutrition, health, and productivity?

06 August 2024 9,618 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View