DEFINE_SR_RATE, reaction only in Porous Region. Warning: Zero number of gas phase reactions, Fluent- Is it usual and any setting wrong?

More Ajith Krishnan's questions See All

Why do we need to neutralize the charge of the system by adding ions before we proceed to energy minimization step in GROMACS ?

I am learning MD simulations using GROMACS and while I was doing a protein in water MD simulation a doubt raised. I was following the steps mentioned on the tutorials page and it said The system...

15 February 2021 5,514 4 View

Divergence detected in AMG solver for temperature and species , DEFINE_VR_RATE, Fluent ?

In 2D Model, Reaction in porous Zone, Error occurs on hooking UDF , DEFINE_VR_RATE in Fluent, .The error spikes just after running calculation after 1st iteration. Divergence detected in AMG...

16 November 2020 9,053 3 View

How to verify if a measuring system is working right?

We have 2 machines that test products. Both of these qualify the product to be Good or Bad ( Based on amount of leak ). The final outcome is attribute variable (Good/ Bad) whereas the way we...

16 November 2020 688 7 View

How to create a surface plot and contour? If i have an excel file with X, Y ,Z values of the surface ( Periphery of a tube) and Q (heat flux) value.?

Need to create 3d surface plot. Data I have X, Y ,Z coordinate of the pipe surface and the corresponding Q (heat flux) values at that point. Nearly 222440 data points of a 2m length pipe. Thank you

07 October 2020 9,854 7 View

Initialization in Fluent? Hybrid initialization or Standard initialization ?

Looking towards an incompressible flow (with K-e, turbulence model), with mass flow/velocity inlet and Pressure outlet boundary condition. Which initialization method preferred? How far it can...

05 October 2020 4,742 5 View

Why did it take humanity so long to start writing though we have been speaking for tens of thousands of years ?

They say we were just speaking and not writing anything for tens of thousands of years till a basic form of writing evolved just about ten thousand years back. Why this yawning gap ?

22 September 2020 5,313 7 View

Which is the best software to simulate chemistry of materials in correlation with their mechanical properties ?

ANSYS or ABAQUS donot correlate materials chemistry wirh the observed or simulated mechanical properties. Is there a software that can do this structure to property correlation. ?

22 September 2020 1,171 3 View

Is there any cost-effective, simple and efficient way to analyse and estimate the amount of vitamins in algal samples?

I am currently pursuing my research in Phycology. I'd like to know if there's any simple and cost-effective method to detect and analyze nutrients and vitamins in the algal matter. The experiment...

18 September 2020 4,081 3 View

Which research institutes in India have an algal identification facility?

I am currently pursuing my research in Phycology and planning to conduct a study on microalgae. Is there any place where I can send my samples to be identified? (Preferably in South India) Also,...

17 September 2020 4,440 2 View

How is the co-expressed genes regulatory network plotted? Is there any Bioinformatics tool for the same?

Hi, I am working on molecular validation of co-expressed genes in Rice under moisture stress. I have a list of genes that are co-expressed in three rice varieties, under a particular set of...

12 July 2020 7,494 1 View

Energy minimization in LAMMPS using NVT ?

How do I do energy minimization in lammps with NVT ensemble ? I am using the following command and it does not seem to work. It stops at extremely high energy and gives me the error zero search...

01 March 2021 2,294 3 View

Why is the sum of the elements in a row in a Q matrix equal to zero?

When explaining substitution models, the substitutions are expressed as Q matrix. Why is the sum of the elements in a row zero?

28 February 2021 3,864 3 View

Why the CHi^2 is close to zero with a bad fitting but the Rp and Rwp are still high?

I am refining my XRD data using in FullProf program. The intensity of the modulated X-ray peaks is almost flat. I tried to adjust the peak intensities but unsuccessful. What is the reason? I guess...

23 February 2021 2,304 4 View

Can we use a compensation matrix with single staining that the negative population for each single staining is below zero?

Recently we used single staining to make a compensation matrix. But, for each single staining we saw that 13 to 25 percent of our negative population had been shown below Zero. In this situation...

21 February 2021 9,982 2 View

How to compare means of continuous data with zero-inflation and skew?

I have two groups (unpaired) of plant biomass measurements and want to know whether there is a test that can be used to determine statistical significance where assumptions are not violated. The...

18 February 2021 1,258 4 View

What does it mean if in mediation analysis the indirect effect is significant but is a larger b value than that of the direct effect?

I understand that for partial mediation to have occured the CI for the indirect effect must not cross zero and the b value for the indirect effect should be smaller than the b value for the direct...

14 February 2021 3,273 7 View

T-test and Mann-Whitney U test on groups with different sample sizes and variances?

Hello I have 2 groups with different sample sizes of (experts: 5 to 8) and (Users: 28 to 35) answering 21 questions on a 7 points Likert scale about the importance of some dimensions for...

31 January 2021 3,885 7 View

How nessesary is working point zero charges for any adesorbent?

How nessesary is working point zero charges for any adesorbent? I want to know how suitable the surface of the material is good for adsorption. I got SEM and FTIR results and thought those are...

30 January 2021 5,120 2 View

How to rotate an anisotropic stiffness matrix to an orthotropic matrix of cancellous bone?

Hi everyone, recently i have a question about how to calculate the orthotropic elastic matrix of cancellous bone cube. I really need the help!!!! I applied six stress states to the cancellous...

21 January 2021 9,143 2 View

Does anyone know how to code a size distribution function in a dynamic model under gProms ?

More specifically, how to integrate the distribution function from zero to infinity at any time to solve a dynamic equation.

20 January 2021 6,994 3 View

Mirosław Grzesik

This is a negative example of using the so-called black boxes as Fluent. If you can't make intermediate prints, you don't know anything.

Ajith Krishnan

@Miroslaw Grzesik, Professor I am a beginner in this chemical engineering field, especially species transport and numerical simulations. Kindly let me know if iam doing anything wrong. Guidances and suggestions will help me to learn more.

Thank you for your reply.