10 October 2014 2 4K Report

Can help me about which is an normal requirements of decarburization in hot forging pieces?.

More Daniel Martinez Krahmer's questions See All
Sheet steel laser cutting?

If you have a laser cutting machine that can cut a steel sheet up to 10 mm thick, is it possible to cut a 20 mm steel sheet in two consecutive passes? If the answer is yes or no, why?

09 October 2019 9,436 3 View

Lubrication regimen in pin on disk test?

I know that a way to establish the lubrication regime in a pin on disk test is by measure the resistance between the pin and the disc. Some papers say that if the resistance is of 2 ohm, the...

05 June 2019 7,949 3 View

How to create a mechanical engineering graphical abstract ?

Hi People. Here in RG there is a similar question but for works in biology. Some of you know if is there any software available to design mechanical engineering graphical abstracts ? Something...

31 December 2018 3,587 2 View

Warm forging of SAE 1045 steel?

Hi People. I need to know the temperture range for making warm forging of SAE 1045 steel.

31 December 2018 4,719 0 View

Hot forging dies made by SAE H13 tool steel?

Please. I need to know what level of hardness provide a equilibrated behaviour between wear resistance and toughness. Also, if a ionic nitriding treatment reduce the friction factor between the...

10 November 2018 6,622 1 View

Redes neuronales artificiales?

Esta pregunta es solo para los amigos y amigas de RG que hablan español. Les quiero preguntar si me pueden recomendar, al juicio de cada uno, cual es el mejor libro en ESPAÑOL para poder aprender...

09 October 2018 8,917 0 View

Turning of low carbon steel?

People. I need your colaboration. What value of hardness do you think is the minimal to not worsen the maquinability level of the steel? I work with steel of 0,1% C. I some of you have a paper, is...

08 September 2018 9,430 3 View

How do I assess ignition risk during magnesium turning?

Some people say that the risk is bigger when the chip particles size are 500 micrometers or minus? What is the reason of this size?

07 August 2018 7,725 0 View

Recrystallization temperature of one steel?

Please. I need information about the recrystallization temperature of SAE 1010 steel, and also the temperature range for warm forging.

05 June 2018 5,844 3 View

Grinding ball manufacturing by hot rolling process?

Hi People. Please, I need to know which is the best material to make the guideline plate in a hot rolling grinding ball machine. Here the is a link to see the...

02 March 2018 832 6 View

Similar questions and discussions
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

What may cause whitish discolor of polycrystalline diamond surface, and cracks near edge?

I am preparing polycrystalline diamond (PCD) with tape casting. The powder is 8~12 um. After drying of tapes, I place several tapes in Ta cup without warm-pressing. Next, debinding is carried...

23 June 2024 7,758 2 View

Is it possible to develop multilayer structure of Thermoset polymer without utilizing adhesives?

The way Hot pressing can be employ for thermoplastic multilayer, any such process or techniques for thermosets as well?

29 May 2024 504 3 View

How do I report and deny forged authorship?

My name was indicated as the only author of the mathematical preprint published on the platform SciProfiles. However, I have never wrote that preprint, or anything similar. How can I decline this...

15 May 2024 4,521 3 View

How do we interpret the origin statement ?

Crystallography Doubt_International Table of Crystallography In the space-group number 185 of ITA (see Attachment), how do we interpret the origin statement?

08 May 2024 10,055 0 View

Hot pressed sintered copper nickel aluminum, copper nickel chromium alloy surface why not mirror?

First ball milling mixed powder, cold pressing, vacuum hot pressing sintering of copper nickel aluminum, copper nickel chromium alloy surface why not mirror, the same process of sintering copper...

21 April 2024 5,387 1 View

Is there a way to improve the fragility of polyethylene terephthalate after hot press?

"Hi, I gasify the polyethylene terephthalate granules and mold them using a hot press at a temperature of 260 degrees Celsius to prepare a bulk sample. However, after molding with the hot press,...

31 March 2024 8,668 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close