09 November 2022 1 9K Report

In the experiment study, samples were collected from the reactor to impinger. How to collect formaldehyde gas samples in the impinger? Can anyone suggest me what types of adsorbent chemical used in the impinger?

More Malathi Rathinasamy's questions See All
Is it possible to run a split ac with 110v battery?

.

10 November 2016 8,442 2 View

How to run MD simulation for metallo enzymes having zn in GROMACS?

I want to do MD simulation for metallo enzyme as well as protein-ligand complex in GROMACS. But when i use the pdb structure with zn ions it showing error. Help me to sort out this problem. Which...

07 November 2016 9,005 3 View

How can I rectify the following GROMACS error? Fatal error: Atom HB3 in residue SER 3 was not found in rtp entry SER with 8 atoms while sorting atoms.

rectify my error Fatal error:Atom HB3 in residue SER 3 was not found in rtp entry SER with 8 atomswhile sorting atoms.

26 March 2015 9,404 12 View

Similar questions and discussions
Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Why do a weight decrease for thermal degradation in nitrogen gas condition?

Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...

26 February 2021 1,100 5 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Can you perform the Murexide test on samples fixed in Formalin?

I have a fixed sample and would like to use the murexide reaction to test for uric acid composition. I no longer have fresh samples

22 February 2021 1,328 1 View

In methylene blue test Why is UV absorbance reading very low as soon adsorbent is added and then increasing before reaching equilibrium?

Hello, I'm working on removal of methylene blue. 01. in the dark test very first reading is taken 15 minutes after adding adsorbent to the dye solution and that UV absorbance reading is very...

19 February 2021 472 5 View

Aspen Plus Error: Unknown or undefined bead number?

Hello, in my Aspen Plus Simulation (see attachment) there are two heat exchangers. One HEX1 (oil+gas) ist fed by hot gas which ist coming out of a burner. The other HEX2 (gas+gas) shall work as a...

14 February 2021 8,096 2 View

Is ANSYS Fluent good for simulation of a three phase reactor(stusy of its hydrodynamics or mass transfer...)?

Hello everybody, I would like to simulate a three phase reactor and study its hydrodynamics. I would like to know which type of software is better? I have a good command of ANSYS Fluent and I am...

10 February 2021 4,303 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close