Dear All,
I did Nyquist plots ac impedance measurements and I found the following plot. Can anyone help me to explain the observer trend with different concentration on steel with blank?
Thanks for your help.
Regards,
B. Thanga Giri
Following the answers
Best of luck
How Educational Technology (ET) is useful for Corrosion Technology (CT)? Bring your idea with EDCT concept for students point of view to improve. Bring your idea with EDCT concept for students'...
09 October 2016 5,645 0 View
How to write the programs in Matlab to get the in-between rage of data in the given data? Please give your valuable suggestions and sample programs?
03 April 2016 8,524 0 View
Dear Prof., Well and wish same from you. What is Star-CD software? What is the use of this software in bio-fuel analysis? Thanks in Advance. Regards, B.Thngagiri
06 July 2015 9,472 0 View
Artificial Neural Networks: Why is the internals of neurons simulated with a linear summation of inputs rather than nonlinear alternatives?
06 July 2015 661 0 View
Which tool is best for learning AI neural network?LISP or MATLAB
06 July 2015 6,333 0 View
What's a good place to start learning about modeling neural networks with MATLAB?
06 July 2015 8,492 0 View
What is the procedure to use the neural network after I have trained it on MATLAB?
06 July 2015 3,631 0 View
What is the best book to learn to make a neural network using Matlab?
06 July 2015 4,088 0 View
What is the argument that neural net skeptics (such as Malik, etc) make to suggest that neural nets are not the best learning algorithms?
06 July 2015 8,259 0 View
Artificial Neural Networks: How are recurrent neural networks different from convolutional neural networks?
06 July 2015 5,861 0 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....
11 July 2024 4,476 3 View
About time dilation. We remember the descriptive diagram which includes, for example, the train which moves at a speed "v". The two mirrors installed in the train between which a beam of light...
03 July 2024 4,332 1 View
Dear colleagues, I'm currently modelling a simple 4-point bending test of a concrete beam in Abaqus. However, the load-displacement curve was ascending (without final point), which didn't match...
29 June 2024 6,192 2 View