Cyclic installation of suction caissons?

Hansini Mallikarachchi @Hansini-Mallikarachchi

04 May 2020 0 9K Report

Hi,

I am looking for some literature about cycling of suction pressure during the installation of caissons. Any suggestions would be much appreciated.

Thanks,

Regards,

Hansini

Badges
Science topic

More Hansini Mallikarachchi's questions See All

Is there an implementation of texture representation using 2D autoregressive models?

I'm trying to study how the texture representation is done using 2D autoregressive models. Although there are a lot of papers describing the theoretical aspects of the process, I'm finding it...

24 November 2018 7,227 3 View

ABAQUS output variable for pore fluid flux in an out of the element?

Hi, I am analysing rate effect in transient consolidation problem in ABAQUS. Could anyone suggest me an output variable which represent transfer of pore fluid flux in an out of the element? My...

21 July 2018 7,878 0 View

Access to pore pressure from UMAT?

Hi, I am using ABAQUS for soil consolidation analysis. Could anyone tell me whether there is a way to access pore pressure at gauss points (from UMAT) Thanks, with regards, Hansini

08 June 2017 802 3 View

Boundary conditions for simulation of simple shear test-2D ?

Hi, I am trying to model a simple shear test in plain strain conditions in ABAQUS. I initially did a single element model. But when I try with multiple elements, I encountered some problems with...

26 October 2016 653 12 View

Can anyone help me calculate soil force on buried anchor plate?

Dear all, I have a very basic problem regarding how abaqus calculate reaction forces of nodes with displacement boundary conditions. I am analysing a vertical anchor plate buried in sand. The...

22 December 2015 3,570 3 View

How to size an liquid jet ejector to raise pressure of suction gas?

How to size an liquid jet ejector to raise pressure of suction gas.I need to get dimensions for simple compression and also for absorption of say CO2 in Water

13 June 2024 4,551 0 View

Do you have updated Clinical Practice Guidelines on Primary Care Dental Services?

Do you require Aerosol suction in every procedure apart from dental prophylaxis? If so what is the ratio of this per dental section, let us say if you have 4 dentists, would one Centralizes...

24 April 2024 8,734 0 View

Can some one help me to analyze the data of filter paper method for soil suction..?

having weight of filter paper initial and final, salt concentration, water percentage, temperature. want total and osmotic suction analysis

21 March 2024 8,669 0 View

How to calculate inertia loss coefficient for reciprocating air compressors?

For reciprocating piston-type air compressors, should inertia losses of air be considered during the phases of suction, compression, expansion, and discharge valve opening? If so, how can the...

04 January 2024 8,224 4 View

Is it normal for 3T3-L1 cells to clump or peel off after removing media and add Q5 media?

I have recently started working with 3T3-L1 cells. After incubate the cells in 96-well plates for 24 hours, I change the media (by suctioning) and add Q5 media. But when I observed the cells...

02 August 2023 6,554 2 View

What are the possible causes for the TEROS 21 sensor to stop working when drying and start working when wetting?

We are using TEROS 21 sensors to obtain the suction along the depth of the Lysimeter. This soil in Lysimeter is subjected to cycles of wetting and drying by making use of the rainfall simulator...

17 March 2023 2,021 0 View

Which case has higher volumetric efficiency?

Take oil injected scroll compressor (Vi = 3) as an example. Case1, Suction pressure = 1 bar, Discharge pressure = 40 bar. Case2, Suction pressure = 30 bar, Discharge pressure = 90 bar. Question:...

19 December 2022 2,182 0 View

Why there are differences between calculation progress and exported chart?

Dear all, I am doing a test run in Plaxis 3D with a suction pile model in layered soil, adding axial compression load and conduct Safety analysis. Loading parameters are input as instruction of...

21 November 2022 9,386 2 View

In the time of synthesis, I found a lot of precipited, when filtered out, then there was no precipited obtained. In this situation, What can I do?

I have started to synthesis Schiff base and metal complexes and found a lot of precipited in round bottom flask or a beaker, when I filtered out through a filter paper or Suction pump, there is no...

04 November 2022 4,354 8 View

Does anybody know why the transverse vortex force exerted on a SCR decreases as the suction resistance factor gets a higher value?

The transverse vortex force and in line vortex force exerted on a SCR have the maximum value near and in the TDZ when the seabed in modeled nonlinear. As the suction resistence has a higher value...

20 October 2022 8,550 0 View