Could someone help me with MPIF Standard 10: “Tension Test Specimens for Pressed and Sintered Metal Powders”,?

01 January 2018 0 7K Report

Please upload the file if available MPIF Standard 10: “Tension Test Specimens for Pressed and Sintered Metal Powders”, Standard Test Methods for Metal Powders and Powder Metallurgy Products, Metal Powder Industries Federation, Princeton, NJ, USA, 2002, p. 62-70.

Badges
Science topic

More Neeraj Kumar Bhoi's questions See All

What should be the typical range of thickness of silicon carbide plate for the effective use as microwave susceptor?

For hybrid microwave heating what should be the range of silicon carbide plate which can perform well in heating and melting process. Can we use 15mm to 20mm thick silicon carbide plate as...

10 November 2018 7,624 2 View

Which Software can be used for the simulation of the Sintering Behaviour of Metal Matrix Composite ?

How to simulate and model the Sintering behavior of the Metal Matrix Composite Material in different Processing Techniques (i.e. Conventional, Microwave and Hybrid Mode) ?

06 July 2018 4,470 2 View

How can we calculate the elastic compliance value of the Al2O3 nano-particle?

I've the XRD data of Al2O3 nano-particle. For the Anisotropy behaviour how we can calculate the elastic complaince value of the particles from the XRD data.

04 May 2018 5,437 3 View

Addition of alloying element during machining gives better surface quality Why ?

Why during machining of light weight or soft material the addition of alloying elements provides good surface finish as compared to base material (Pure form of metal).

10 November 2017 8,372 5 View

What is the significant of micro and macro hardness?

For metal matrix composite material (Al matrix composites) what is the importance of measuring micro and macro hardness after final processing of material?

10 November 2017 7,782 6 View

Why is the rate of reaction increased when magnesium is powdered rather than in solid form?

why chemical stability of magnesium in powder is less

09 October 2017 3,986 2 View

What is the status of bread making and more bakery foods with the use of insect flour/powder?

Insects have been consumed by human diet since prehistoric times. At present, the idea of looking at insects as food has been getting traction worldwide, also in response to increasing food...

03 March 2021 6,223 5 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

How to reduce static electricity of powder after lyophilization?

I am working on synthesizing and then purifying peptides using the SPPS system. After purification of the peptide, the peptide powder is obtained using a freeze dryer. When measuring the powder,...

22 February 2021 10,099 5 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

How to Study a proton NMR of Graphene prepared by Electrochemical Exfoliation technique?

I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.

21 February 2021 8,947 3 View