How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

Mixed ANOVA or Multilevel modeling?

Hi everyone, I'm having some questions about choosing the right test for my experiment and I hope I can find help here! Here are the settings of the experiment: 1. participants are randomly...

14 February 2021 1,028 4 View

How to do variation partition for a distance matrix for microbial ecology?

I have bacterial, fungal, and protist OTU table. I want to know to what extent protist and fungi distribution can explain the bacteria distribution. I only know Mantel test could do a correlation...

11 January 2021 4,164 2 View

Are there any method to detect implanted stem cells?

Dear, We developed a microcarrier that was pre-seeded hUC-MSCs to repair a rat bone defect. However, we didn't use GFP or Luciferin to track cell survival. If there's any way to identify the...

15 December 2020 6,065 3 View

How to characterize the dispersion of aluminum oxide in Al matrix composite which reinforced by alumina during the powder metallurgy?

Now we could characterize the disperion of Al2O3 in AMCs (pure Al reinforced by Al2O3 ) after sintering. But the process of powder metallurgy has a lot of steps, which take long time. The cycle...

08 November 2020 5,244 3 View

Is that possible the filter of flow cytometry was failed so I got those data using FL1 vs FL2 and FL1 vs FL3?

The cells were expressing GFP and also incubated with PI for dead cells detection. This is my first-time using this BD Accuri C6 and I'm not sure if I need to set compensation (I tried to follow...

01 November 2020 8,360 3 View

What if the abbreviations of two technical terms in the manuscript are the same?

I'm wrting an article, there are two terms "Carboxymethylcellulose" and "Critical Micelle Concentratio" both have the abbreviations of "CMC". How should i distinguish them?

23 June 2020 2,115 5 View

ImzMLConverter installation & running issues?

Hi Everyone, Did anyone have a similar issue when install and run imzMLConverter? I followed the instruction on https://www.cs.bham.ac.uk/~ibs/imzMLConverter/ and used the command it provides....

23 May 2020 3,936 3 View

How to revise survey items based on unexpected EFA results?

Hi, there. A few days ago, I posed a question about factor analysis of survey results, but I left many important details unspecified. HERE is the more detailed one. I develop a theoretical model...

06 May 2020 4,937 10 View

Many cases of identical answers to consectutive questions.How to revise survey items?

Hi, there. I am working on my Ph.D dissertation. I have run a factor analysis of 56 items with maximum likelihood and direct oblimin method. It turns out that only one factor can be extracted...

25 April 2020 6,267 10 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View