Could anybody help me out in Flux Magnitude and Angle Control (FMAC) of DFIG?

More Ganesh P. Prajapat's questions See All

How to coat sln with eudragit s 100 and eudragit fs 30d ?

SLN

30 May 2024 9,109 0 View

How to insert the molecules in gromacs based on surface area of polymer molecules ?

And also how to compress the system based on surface area of system such that we get new gromacs file at different surface area of polymer molecule? i heard on the fly approach can be used but i...

16 April 2024 2,409 2 View

Which are the best ways to analyze the data of PM2.5 & PM10 in the atmosphere collected by gravimetric analysis?

14 April 2024 3,953 3 View

Mass scaling in ABAQUS ?

I need to perform mass scaling for a certain period and remove it in further analysis in Abaqus. Does anyone assist me with this?

04 March 2024 3,203 1 View

How to model a resistor whose resistance can be varied w.r.t time or temperature in MTALAB, kindly help?or do i get a ready element with such feature?

MATLAB,

25 February 2024 5,052 2 View

How do i represent electric ARC in MATLAB and measure its parameters like voltage, current and temperature, kindly help me with the circuit?

MATLAB simulink

22 February 2024 6,330 2 View

When crystal field splitting does not occur even in the presence of ligand?

For example: In M(^3+)VO4 (M = transition metal, Fe, Cr, .....) there are M^(3+)O6 octahedral group surrounded by (VO4)^3- tetrahedral group by corner shearing. Therefore, Is the crystal field...

26 January 2024 7,486 0 View

Currently, i am working on DFT modelling in BURAI 1.3 (Quantum espresso). While i am running my simulation, error was appeared as shown below image?

If anyone has any kind of solution for this error, please help me out.

07 December 2023 978 2 View

How we find purity of extracted cellulose using FTIR analysis?

What is the method for determination of cellulose purity using FTIR analysis which is extracted by waste biomass?

30 October 2023 2,409 1 View

What is the method for determination of purity of cellulose extracted from biomass?

There is method available for determination of chemical composition of cellulose. However , I cannot find any method which shows the purity of the cellulose which is extracted from waste biomass....

22 October 2023 7,462 5 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Are there any good simple systems or platforms to recommend?

In order to show people the beauty of control and enhance enthusiasm for learning control theories, are there any good simple systems or platforms to recommend?

05 August 2024 10,034 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Christian E. Jacob

Dear Ganesh, one example of application of DFIG you can find in attached link. This proceeding delivers a survey of steady-state and dynamic modelling of DFIG.

Article New Drive Converter and Digital Control for the Pulsed Power...

Ganesh P. Prajapat

Thank you @Jacob sir.

But, actually, i am using state model of dfig along with wind turbine and i also have to perform MPPT for the variable speed in the controller.

Mahdi Doustmohammadi

You can Look at here

http://cdn.intechopen.com/pdfs-wm/16255.pdf

Thanks @ Mahdi sir