What is the most suitable NMR solvent for carbon-based materials?

What is the most suitable NMR solvent for carbon-based materials?

25 December 2020 5,020 4 View

Effect of vibration on Heat transfer of fluid in pipe - COMSOL Physics?

We have a one meter long copper pipe through which water passes at a certain speed. The outer wall of the tube is covered by the heater where all the energy of the heater is transferred to the...

21 December 2020 8,954 8 View

Effect of adsorbent porosity on efficiency of adsorbent recovery ?

Hi guys. Can anyone answer the following with citing the references? 1) Relationship between adsorbent porosity and adsorption/desorption rate? 2)Relationship between porosity and adsorbent...

31 October 2020 6,323 5 View

Any recommendation for a good Machine learning course (with available materials for instructors)?

Hello everyone, I am looking for a good recommendation for a Machine learning course (with available materials). Which one do you suggest? Something that would be up to date with available...

15 September 2020 1,674 17 View

How to capture the geometry of rubble piles / collapsed structures beneath the surface via remote sensing?

Hi dear community, I am currently working on a project where I want to generate a 3D reconstructed model consisting of rubble piles (in consequence of a building collapse) via remote sensing. In...

10 September 2020 4,685 4 View

How can I insert an assembeled system, meshed by SOLIDWORKS, to ANSYS?

I already did it before but this time as the model is complicated I have faced with tis error: The surface mesh is intersecting or close to intersecting,making it difficult to create a volume...

05 September 2020 9,558 1 View

Raman peak shift or uncertainty?

Good day, I have a Raman spectra for 4 samples including Graphene oxide (GO) and its nanocomposites. According to the attached figure can sb tell me whether the different peak positions of the...

15 June 2020 6,467 8 View

Anyone in kolkata working of LNCaP prostate cells?

I am working with prostate cancer cells, i want to know who is presently working with PCa cell lines in viro and in vivo in kolkata.any leeds will of great help.

07 March 2020 7,831 1 View

How to model a fluid-structure interaction (FSI) Hyperelastic beam?

I am trying to model a fluid-structure interaction (FSI) Hyperelastic beam in COMSOL Multiphysics. The model works fine for low inlet flow velocity like 0.016 [m/s], but it gives the error below...

02 February 2020 3,394 3 View

How ferroelectricity may affect the photovoltaic performance in Perovskite solar cell?

how ferroelectricity can improve the efficiency of solar cell and what parameters are important in this relation?

01 February 2020 8,331 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View