09 September 2014 2 5K Report

Hi,

I am working on a key management and Cluster scheme for wirless sensor nodes using contiki os. The simulations (in cooja) run perfectly for ubuntu 12.04 LTS (32 bit). However in Ubuntu 14.04.1 LTS (64 bit). It gives me error: Writing to read-only P3IN.

Could this be an error due to newer versions of MSP430-gcc or due to the 64-bit os? Or is it something entirely different. Please help!

Thank you,

Avijit

Java stack trace

Caused by: se.sics.mspsim.core.EmulationException: Writing to readd-only P3IN

More Avijit Mathur's questions See All
Contiki OS compatibility: Rime comms stack with IPv6?

I have a wireless sensor network running RIME stack on contiki os. I wish to connect this network to the outside Internet (IPv6). My question is that whether Rime is compatible with IPv6? Because...

05 June 2015 3,405 0 View

Similar questions and discussions
Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How can I retrieve FASTA sequence from gene ID or UID of a Gene ? I have GeneBank IDs ?

I treid to use Entrez Batch, but it redirects me to NCBI site. Is there any script of Linux or Python through which I can download Fasta sequence of list of gene ID ?

21 February 2021 7,783 12 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View

What should a smart water system look like?

Our team is designing a smart water C&C dashboard for a smart city initiative. As we look into the current smart water system landscape, we couldn't reconcile to a definitive solution that...

16 February 2021 1,094 3 View

Receiving very less number of hits and events in acoustic emission tests?

I am doing a three point bend test with concrete specimen of dimension 280mm*90mm*90mm. I am putting 2 sensors near the notch with 3cms away from both the sides. the experiment ran for 20 mins but...

13 February 2021 2,990 1 View

How to increase coupling range (distance between reader and sensor coils) in LC resonance circuit?

Hello great researchers, I am working on a wireless pressure monitoring project where sensing part is actually an LC resonance sensor and I am using a planar coil as a reader to get wireless...

11 February 2021 4,148 5 View

I am looking for a microbend optical sensor design...can anyone please provide me some idea about it??

I am working on a landslide model...i need an optical sensor to determine the amount of pore pressure and other values..i am thinking of using a microbend sensor. Can anyone please provide me with...

11 February 2021 5,911 2 View

How to eliminate noise when using a sensor with instrumentation amplifier and giving it's output to Arduino?

When I am trying to implement a pressure sensor through instrumentation amplifier and then giving it's output to Arduino, I am getting garbage value due to noise, so how to eliminate it.

05 February 2021 8,598 11 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close