Hi,
i am little confused about the term cohesive zone length in delamination modeling of composites. is it the thickness of cohesive zone? or something else?
Thank you in advance
https://www.sciencedirect.com/search?qs=Cohesive%20zone%20length&show=25&sortBy=relevance
It is a very interested question
This larva was captured using a plankton net in the Persian Gulf during the summer. I believe it may be a Facetotecta nauplius.
08 August 2024 3,746 4 View
Dear Researchers I need to know, how to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field data in Tecplot? Thank You
02 August 2024 3,615 1 View
how is prion can cause disease
01 August 2024 250 1 View
I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...
29 July 2024 950 4 View
We are working on a robot that cleans solar panels using fresh water supply and a rotating brush. We are trying to conserve as much water at possible by recycling the dirty water that is collected...
28 July 2024 5,778 2 View
Is it feasible to employ an artificial sun in the experimental investigation of concentrated solar energy systems, specifically linear Fresnel systems? If the answer is affirmative, what type of...
22 July 2024 9,710 6 View
Is it the best optimization ratio based on experiments?
22 July 2024 8,170 0 View
Can diamond be grown using molecular beam epitaxy?
22 July 2024 9,755 2 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
In deriving a model of an LTI dynamic system, the model of the system does have no RHP zeros, however, when inspecting the step response, it reveals a non-minimum phase system represented by a...
14 July 2024 6,355 2 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks
06 August 2024 949 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
How to design VN primer to attach with universal reverse primer
05 August 2024 2,116 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View