Chemical solution to etch sintered tungsten titanium ?

More Umi Zalilah Mohamad Zaidi's questions See All

How can i find co author?

I need help for writing a chapter.

15 May 2024 3,963 2 View

Are there any EPA/WHO trace elements standards in sediment available for Cd, Cu, Fe, Ni, Mn, Pb, Co, Cr, Zn, As?

Any links or table will be appreciable

08 February 2024 1,163 1 View

Can anyone suggest me few articles, where Primary & Secondary data analysis is done with Machine Learning & Deep Learning Models?

Hello, I am looking for articles in which the analysis is done with the Machine Learning Models and Neural Networks. Kindly suggest any such articles published within last 1 or 2 years. Thank...

17 January 2024 9,303 5 View

Can Any Researcher in Atomic and molecular Physics help me find values of first five excited states of Hydrogen molecule in units of electron volts?

First excited state of Hydrogen molecule can be found easily. I need to know 4 more values to compare with my calculations. Thanks.

05 December 2023 2,637 4 View

Phase Grain Contiguity & Bonding Phase Thickness of Powder Composite?

Hi. Can anyone explain to me these terms: 1) Phase grain contiguity 2) Bonding phase thickness Q: Simple explanation on this? How to measure this properties? Software / formula ? How does this...

03 December 2023 4,823 1 View

"Which is better for studying the idea of a startup, BMC or Lean Canevas?

"The advantage between..."BMC and The Lean Canevas...

23 October 2023 8,912 2 View

What occupation adversely affects your fine motor skills?

the causes, effects and solutions of weak fine motor skills due to that occupation/job/habit.

08 October 2023 1,032 3 View

Visit lab to elaborate ZnS thin films?

I need invitation letter to visit lab for elaborate ZnS co doped (Co, Ag) in October or November 2023

15 August 2023 8,597 1 View

Black & Scholes PDE into ODE ?

I am currently working on a research project involving the numerical solution of the Black-Scholes partial differential equation (PDE) for option pricing. To simplify the problem, I am interested...

09 June 2023 2,830 5 View

Any one experience to load mRNA in iMSC derived exosomes/EVs, through electroporation?

Hello Everyone, I want an exosome mediated delivery of mRNA, for that exosome loading is required through electroporation. I searched a lot for an optimized protocol for electroporation of mRNA...

20 May 2023 3,782 1 View

Non -oxidizing metal binders?

I'm trying to sinter some Nb parts and I'm trying to find a binder which does not produce oxidative compounds when it decomposes.

25 July 2024 9,823 3 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

How to change the author?

Hello! Research of factors affecting thickness of the covering obtained by electro contact sintering of composite materials. This is my article, not Varvara. How to change the author? Incorrect...

09 July 2024 3,829 0 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View

What may cause whitish discolor of polycrystalline diamond surface, and cracks near edge?

I am preparing polycrystalline diamond (PCD) with tape casting. The powder is 8~12 um. After drying of tapes, I place several tapes in Ta cup without warm-pressing. Next, debinding is carried...

23 June 2024 7,758 2 View

Can anyone suggest an adhesive that can sustain 600C?

I have to join tungsten wire to metallic plate with that adhesive and entire assembly has to be heated upto 600C in ultra high vacuum. I know about zirconia paste but it is not readily available...

18 June 2024 3,092 3 View

The pressure drop of porous media keeps increasing, why?

Hi y'all, I was trying to meausre the pressure drop under a constant flow rate. For the porous media like titanium fiber felt and sintered titanium, when I use deionized water OR alcohol,the...

02 June 2024 2,951 2 View

[SOLVED] Philips SEM XL30 (Tungsten Filament): HT not working after pressure failure?

Dear fellow researchers, We are currently operating a Philips XL30 Scanning Electron Microscope (SEM) equipped with a tungsten filament and have encountered a significant issue. Recently, our...

28 May 2024 232 2 View

[SOLVED] Philips SEM XL30 (Tungsten Filament): HT not working after pressure failure?

Dear fellow researchers, We are currently operating a Philips XL30 Scanning Electron Microscope (SEM) equipped with a tungsten filament and have encountered a significant issue. Recently, our...

28 May 2024 9,415 2 View

Can someone give me some links to papers where sintering is done using vacuum sealed silicate glass tubes?

I am trying to sinter my samples at 1300 degree celsius in Vacuum and I came to know about a technique from some lab technicians that it can be done using box or muffle furnace itself. The idea is...

26 May 2024 9,850 4 View

Vadim Verlotski

For SEM you don't need any etching, as the contrast between titanium and tungsten will be very good anyway. Etching is only needed for optical microscopy.

Özgün Ceren Akbay

Dear Umi Zalilah Mohamad Zaidi

I had a study using CoCr alloy, maybe it will be useful for you.

"Productıon and Cleaning of Lattice Structures Used in the Space and Aerospace Industry with Metal Additive Manufacturing Method"

Kind Regards.